Hub Oil (Flexxaire Fan) - Add
Catatan: Before you proceed, ensure that you know the correct model of the hydraulic actuated fan.
Perform the following procedures in order to add oil to the fan hub.
Adding Oil to the Hubs of FX 2000 Hydraulic Actuated Fans
Show/hide table
Ilustrasi 1 | g00898973 |
- Rotate the hub until one of the oil drain plugs (1) or ( 2) is facing upward.
- Remove oil drain plug (1) and oil drain plug (2).
Show/hide table
Ilustrasi 2 g00920211 - Insert a suitable dipstick into the hub. Use the dipstick to measure distance (A).
- Add oil until dimension (A) is between
82,55 mm (3,25 inch) and85,72 mm (3,375 inch) . See Operation and Maintenance Manual , "Lubricant Viscosities and Refill Capacities" for the appropriate type of oil.Catatan: Do NOT overfill the hub. An air space is required to allow the oil to expand. Failure to leave the desired air space will result in failure of the seals.
- Allow the oil to settle in the hub. If you use synthetic oil, allow extra time for the oil to settle. Recheck the oil level. Add additional oil, if necessary.
Catatan: Do not overfill the hub. An air space is required. The air space will allow the oil to expand. Failure to leave an air space may result in seal failure.
- Apply Sealant 6V-6640 to the threads of the oil drain plug. Reinstall the plug.
- Check for any leaks and make any necessary repairs before operating the fan.
Caterpillar Information System:
Reuse and Salvage for Cylinder Head Assemblies {1100, 1101, 1103, 1104, 1105, 1106, 1108, 1109, 1115, 1117, 1121, 1124, 1125} Reuse and Salvage for Cylinder Head Assemblies {1100, 1101, 1103, 1104, 1105, 1106, 1108, 1109, 1115, 1117, 1121, 1124, 1125}
1090, 1190, 1190T and 1290T Track Feller Bunchers Hood Tilting
C11 and C15 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
773F Off-Highway Truck and 775F Off-Highway Truck Power Train Rear Axle and Final Drive System
583T Pipelayer Engine Supplement Bottom Guard - Install
583T Pipelayer Engine Supplement Bottom Guard - Remove
1090, 1190, 1190T and 1290T Track Feller Bunchers Monitoring System - Information about System Operation
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Position Sensor (Rear Steering) - Remove and Install
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 0600 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 0600 - FMI 03
12M Motor Grader Oil Filter (Implement Controls) - Replace
120M and 12M Motor Graders Oil Filter (Hydraulic Tank Return) - Replace
1390 Track Feller Buncher Hub Oil (Flexxaire Fan) - Change
770 and 772 Off-Highway Truck Daily Inspection
C4.4 Industrial Engine Finding Top Center Position for No. 1 Piston
773F Off-Highway Truck and 775F Off-Highway Truck Power Train Power Train Hydraulic System Troubleshooting
583T Pipelayer Engine Supplement Engine Side Guards - Remove and Install
2006/10/30 Improved Hoist Cylinders Are Used {5102}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2113 - FMI 03
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2113 - FMI 04
1390 Track Feller Buncher Hub Oil Level (Flexxaire Fan) - Check
773G and 775G Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet) Pressure - Test
325D Material Handler Circuit Breakers - Reset
773F Off-Highway Truck and 775F Off-Highway Truck Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust