Seat Belt Reminder System
Your machine is equipped with a Seat Belt Reminder system. The system will notify the operator when the seat belt is not fastened while the machine is in operation.
If the seat belt is not fastened, and the ignition key is in the ON position. A seat belt reminder indicator will be shown in the LCD portion of the indication display.
Show/hide table
| |
| Illustration 1 | g03893359 |
If the seat belt is not fastened when the machine is placed into operation, an indicator will appear on the indication display and an audible alarm will sound.
The machine is considered to be in operation if any of the following conditions apply:
- The transmission is in any gear other than neutral
- The implement controls are being activated
- Transmission calibration or service mode is active
The alert routine can be interrupted by either fastening the seat belt or by returning the machine to an "Idle" state.
The machine is considered to be in an Idle state under the following conditions:
- Engine is not running
- Engine running and actual gear is neutral
- Implement operating status is inactive
- Transmission calibration or service modes are not actively running
Caterpillar Information System:
D5R and D6N Track-Type Tractor Machine Systems Hydraulic Tank - Assemble
Procedure to Rework the Governor and Brake Pedal for Certain D3K2, D4K2, and D5K2 Small Track Type Tractors {4122} Procedure to Rework the Governor and Brake Pedal for Certain D3K2, D4K2, and D5K2 Small Track Type Tractors {4122}
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System Calibrations, Diagnostic Tests (Cat ET)
Procedure to Install Grease Line in the Front Lines Group on Certain 980M and 982M Wheel Loaders {7510, 7540} Procedure to Install Grease Line in the Front Lines Group on Certain 980M and 982M Wheel Loaders {7510, 7540}
973K Track Type Loader Maintenance Interval Schedule
Improved Grease Line in the Front Lines Group Is Now Used on Certain 980M and 982M Wheel Loaders {7510, 7540} Improved Grease Line in the Front Lines Group Is Now Used on Certain 980M and 982M Wheel Loaders {7510, 7540}
Bench Test Procedure for a 631K and 637K Wheel Tractor Scraper Transmission {0599, 3030, 3073} Bench Test Procedure for a 631K and 637K Wheel Tractor Scraper Transmission {0599, 3030, 3073}
3512E and 3516E Marine Engines Control Cabinet - Assemble
814K Wheel Dozer Machine Systems Operator Platform - Remove and Install
D5R and D6N Track-Type Tractor Machine Systems Hydraulic Tank - Disassemble
992K Wheel Loader Fuel System Primary Filter (Water Separator) - Check/Drain
D5R and D6N Track-Type Tractor Engine Supplement Belt Tensioner - Remove and Install
An Improved Dust Ejector Hose is Now Available for Certain 988K Large Wheel Loaders, 834K Large Wheel Dozers, and 836K Compactors {1068, 7554} An Improved Dust Ejector Hose is Now Available for Certain 988K Large Wheel Loaders, 834K Large Wheel Dozers, and 836K Compactors {1068, 7554}
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Declaration of Conformity
910M, 914M, 918M, 910K, and 914K Compact Wheel Loaders, Engine Supplement Diesel Exhaust Fluid Tank - Remove and Install
Track Shoes Are Service-Replaced On Some D6 Track-Type Tractors {4170} Track Shoes Are Service-Replaced On Some D6 Track-Type Tractors {4170}
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Operation
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Safety Messages
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System General Information (Fan Hydraulic System)
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System Location of Components (Fan Hydraulic System)
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System Gear Motor (Hydraulic Fan)
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Specifications
C175-16 and C175-20 Locomotive Engines Accumulator (Fuel Injection) - Remove and Install
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Electronic Control (Hydraulic System)