Control Cabinet - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
不正确处理化学用品会导致个人受伤。 确保您使用了本作业要求的必需防护用品。 确保阅读并理解所使用的任何化学用品的标签和材料安全数据表上所述的所有说明和危险。 遵循化学用品制造商建议的有关化学用品搬运、储存和废弃的所有安全注意事项。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关收集和盛接 Cat® 产品油液的合适工具和用品,请参阅专门出版物, PERJ1017, "代理商维修工具目录"。 按照本地法规和要求处置所有油液。 |
- 将压力传感器总成 (56) 安装到歧管总成 (54) 中。 将压力传感器总成 (56) 拧紧至扭矩为
10 ± 2 N·m (90 ± 18 lb in) 。 - 将电磁阀总成 (57) 安装到歧管总成 (54) 中。 将电磁阀总成 (57) 拧紧至扭矩为
105 ± 10 N·m (77 ± 7 lb ft) 。 - 如有需要,定位电磁阀总成 (57)。 将电磁阀后部的螺母拧紧至扭矩为
5.4 ± 0.6 N·m (48 ± 5.25 lb in) 。 - 将调节器 (58) 安装在歧管总成 (54) 中。 拧紧调节器 (58) 至扭矩为
140 ± 14 N·m (103 ± 10 lb ft) 。Show/hide table图 2 g06091291 - 将歧管总成 (54) 安装到控制机柜上。 安装螺栓 (55)。
Show/hide table
图 3 g06091280 - 将线束组件 (53) 安装到控制机柜上。 连接现有接头并用电缆扎带固定线束。
Show/hide table
图 4 g06092777 - 将膜片 (52) 安装到泵总成上。
Show/hide table
图 5 g06092776 - 将泵盖 (50) 和螺栓 (51) 安装到泵总成上。
Show/hide table
图 6 g06092778 - 按所示顺序拧紧螺栓 (51)。
Show/hide table
图 7 g06092774 - 将阀组件 (48) 和阀组件 (49) 安装到柴油机排气处理液泵总成 (38) 上。
注: 确保阀组件上的流量指示器指示正确方向。
Show/hide table图 8 g06091251 - 将电磁阀总成 (41) 和电磁阀总成 (43) 安装到歧管总成上。 将电磁阀总成拧紧至扭矩为
130 ± 10 N·m (96 ± 7 lb ft) 。 - 如有需要,定位电磁阀总成。 将电磁阀后部的螺母拧紧至扭矩为
5.4 ± 0.6 N·m (48 ± 5.25 lb in) 。 - 将温度传感器总成 (45) 安装到歧管总成上。 将温度传感器总成 (45) 拧紧至扭矩为
48 ± 5 N·m (35 ± 3.5 lb ft) 。 - 将压力传感器总成 (44) 安装到歧管总成上。 将压力传感器总成 (44) 拧紧至扭矩为
20 ± 3 N·m (177 ± 26.5 lb in) 。 - 将适配器组件 (42) 和适配器组件 (47) 安装到歧管总成上。
- 将加热器组件 (46) 安装到歧管总成上。
Show/hide table
图 9 g06092518 - 将柴油机排气处理液泵总成 (38) 连接至歧管总成 (39)。 安装螺栓 (40)。
Show/hide table
图 10 g06092779 - 按所示顺序拧紧螺栓 (40)。
Show/hide table
图 11 g06091234 - 将歧管总成 (39) 和柴油机排气处理液泵总成 (39) 作为一个组件进行安装。 安装杆 (37) 和锁紧螺母 (36)。
Show/hide table
图 12 g06092602 - 将线束组件 (32) 连接至接盒线。 将线束组件 (33) 连接到泵加热器上。 将线束组件 (34) 和线束组件 (35) 连接到泵总成上。
Show/hide table
图 13 g06091228 - 将线束组件 (24) 连接到温度传感器上。 将线束组件 (25) 连接到加热器总成上。 将线束组件 (26) 连接到压力传感器上。 将线束组件 (27) 和线束组件 (28) 连接到电磁阀总成上。
Show/hide table
图 14 g06092673 - 将盖适配器 (25) 安装到罐组件 (23) 上。
Show/hide table
图 15 g06092677 - 将滤网 (26) 装入罐组件 (23)。
Show/hide table
图 16 g06092667 - 将罐盖 (24) 安装到罐组件 (23) 上。
Show/hide table
图 17 g06091214 - 将罐组件 (23) 安装到控制机柜上。 安装扎带组件 (22)。 连接两个加热器组件。
- 安装加热器 (27)。 将线束组件连接到加热器 (27) 上。
Show/hide table
图 18 g06091188 - 将软管组件 (19)、 (20) 和 (21) 安装在罐组件和歧管总成之间。
Show/hide table
图 19 g06091185 - 安装开关组件 (16) 和螺栓 (18)。
Show/hide table
图 20 g06091171 - 安装螺母以将线束组件 (17) 连接至开关组件 (16)。
Show/hide table
图 21 g06091147 - 将通风装置安装到罐组件上。 将软管 (15) 连接到通风装置上。
Show/hide table
图 22 g06091145 - 将液位传感器组件 (14) 安装到罐组件上并用机器螺钉固定。
- 断开液位传感器组件 (14) 的线束组件。
Show/hide table
图 23 g06091136 - 安装电子控制总成 (11)、螺栓和螺柱 (13)、安装件以及隔套。
Show/hide table
图 24 g06091124 - 将线束组件 (10) 和线束组件 (12) 连接到电子控制总成 (11) 上。
Show/hide table
图 25 g06091121 - 安装前门 (9) 并用螺栓 (8) 固定。
Show/hide table
图 26 g06091115 - 安装门组件 (7) 和螺栓 (6)。
Show/hide table
图 27 g06091111 - 安装接头 (4)。 放置软管并拧紧卡箍 (5)。
Show/hide table
图 28 g06091098 - 安装侧门 (3) 和螺栓 (2)。 对另一侧重复上述步骤。
Show/hide table
图 29 g06091087 - 将适配器组件 (1) 安装到机柜组件上。
- 用尿素加注罐组件。
Show/hide table
图 1 | g06091298 |
Caterpillar Information System:
814K Wheel Dozer Machine Systems Operator Platform - Remove and Install
D5R and D6N Track-Type Tractor Machine Systems Hydraulic Tank - Disassemble
992K Wheel Loader Fuel System Primary Filter (Water Separator) - Check/Drain
D5R and D6N Track-Type Tractor Engine Supplement Belt Tensioner - Remove and Install
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Location of Components (Hydraulic System)
D5R and D6N Track-Type Tractor Machine Systems Hydraulic Tank - Remove and Install
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System Gear Pump (Implement) - 910K, 910M
814K Wheel Dozer Machine Systems Hydraulic Tank - Assemble
New Door Seal To Improve Rattling And Sealing Of Door In Certain D6T Track-Type Tractors {7308} New Door Seal To Improve Rattling And Sealing Of Door In Certain D6T Track-Type Tractors {7308}
814K Wheel Dozer Machine Systems Hydraulic Tank - Disassemble
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Hydraulic System)
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System Relief Valve (Main)
Bench Test Procedure for a 631K and 637K Wheel Tractor Scraper Transmission {0599, 3030, 3073} Bench Test Procedure for a 631K and 637K Wheel Tractor Scraper Transmission {0599, 3030, 3073}
Improved Grease Line in the Front Lines Group Is Now Used on Certain 980M and 982M Wheel Loaders {7510, 7540} Improved Grease Line in the Front Lines Group Is Now Used on Certain 980M and 982M Wheel Loaders {7510, 7540}
973K Track Type Loader Maintenance Interval Schedule
Procedure to Install Grease Line in the Front Lines Group on Certain 980M and 982M Wheel Loaders {7510, 7540} Procedure to Install Grease Line in the Front Lines Group on Certain 980M and 982M Wheel Loaders {7510, 7540}
910K, 910M, 914K, 914M, 918M, and 920K Wheel Loaders Machine System Calibrations, Diagnostic Tests (Cat ET)
Procedure to Rework the Governor and Brake Pedal for Certain D3K2, D4K2, and D5K2 Small Track Type Tractors {4122} Procedure to Rework the Governor and Brake Pedal for Certain D3K2, D4K2, and D5K2 Small Track Type Tractors {4122}
D5R and D6N Track-Type Tractor Machine Systems Hydraulic Tank - Assemble
854K Wheel Dozer Seat Belt Reminder System
An Improved Dust Ejector Hose is Now Available for Certain 988K Large Wheel Loaders, 834K Large Wheel Dozers, and 836K Compactors {1068, 7554} An Improved Dust Ejector Hose is Now Available for Certain 988K Large Wheel Loaders, 834K Large Wheel Dozers, and 836K Compactors {1068, 7554}
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Declaration of Conformity
910M, 914M, 918M, 910K, and 914K Compact Wheel Loaders, Engine Supplement Diesel Exhaust Fluid Tank - Remove and Install
Track Shoes Are Service-Replaced On Some D6 Track-Type Tractors {4170} Track Shoes Are Service-Replaced On Some D6 Track-Type Tractors {4170}