Water Pump - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
C | 1P-0510 | 冲头总成 | 1 |
D | 139-0088 | 油封起子 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 唇形密封 (13) 带有纸板芯 (14)。 纸板芯用来定位密封。 安装轴 (10) 之前不要拆下纸板芯。 纸板芯 (14) 用来定位轴安装中的唇形密封。
Show/hide table
图 2 g01101258 - 利用工具 (C) 安装唇形密封 (13)。
- 将轴安装到唇形密封中。 拆下纸板芯。
Show/hide table
图 3 g01101106 - 将轴承组件 (9) 定位到水泵壳内的轴上。
- 安装挡圈 (8) 和螺栓 (7)。
Show/hide table
图 4 g01101105 - 定位齿轮 (6) 后安装螺栓 (5)。
Show/hide table
图 5 g01101108 - 翻转水泵并将密封组件 (12) 定位到轴 (10) 上。 利用工具 (D) 和适当压具安装密封组件 (12)。
- 利用工具 (D) 和适当压具将环 (11) 安装到轴 (10) 上。
Show/hide table
图 6 g01101272 - 将叶轮 (4) 安装在轴上并拧紧螺栓 (3) 至扭矩
39 ± 3 N·m (29 ± 2 lb ft) 。 - 检查过渡接头 (1) 上 O 形密封圈 (2) 的状态。 在 O 形密封圈上涂抹干净的机油。
- 安装过渡接头 (1) 和 O 形密封圈 (2)。
Show/hide table
图 1 | g01101251 |
结束:
- 安装水泵。 请参阅拆解和组装, "水泵 - 安装"。
Caterpillar Information System:
Digital Voltage Regulator Voltage Regulation
Digital Voltage Regulator Power Factor Regulation
Digital Voltage Regulator KVAR Regulation
G3606 and G3608 Engines Housing (Front) - Remove
G3606 and G3608 Engines Magnetic Pickup - Remove and Install
G3606 and G3608 Engines Idler Gears (Front) - Install
G3606 and G3608 Engines Idler Gears (Front) - Remove
G3408 and G3412 Engines Air Inlet and Exhaust System
G3408 and G3412 Engines Ignition System
G3606 and G3608 Engines Idler Gears (Rear) - Install
G3606 and G3608 Engines Idler Gears (Rear) - Remove
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Disassemble
Digital Voltage Regulator Line Loss Compensation
G3606 and G3608 Engines Housing (Front) - Install
Digital Voltage Regulator Reactive Voltage Droop
G3408C and G3412C Engines Lubrication System
Digital Voltage Regulator Cross Current Compensation
PM3412C Power Modules Stopping the Engine
797 Off-Highway Truck Hydraulic System Solenoid Valve (Hoist Pilot)
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Sensors
G3606 and G3608 Engines Manual Barring Group - Remove
G3408 and G3412 Engines Cooling System
G3408 and G3412 Engines Basic Block
G3606 and G3608 Engines Manual Barring Group - Install