Control Valve (Auxiliary)(Loader) (Mechanically Operated)
Show/hide table
 | |
| Illustration 1 | g00758247 |
191-4035 Control Valve (Auxiliary) | |
(1) Torque for the housing ... 10.0 ± 1.0 N·m (89.00 ± 9.00 lb in)
(2) 187-0530 Relief Valve
- Torque for the relief valve ... 70.0 ± 7.0 N·m (52.00 ± 5.00 lb ft)
- Relief valve pressure at a flow rate of 2.0 ± 0.5 L/min (0.50 ± 0.13 US gpm) ... 27,600.0 ± 350.0 kPa (4000.00 ± 50.00 psi)
(3) Torque for the bolts ... 5.0 ± 0.5 N·m (44.00 ± 4.00 lb in)
(4) Torque that is needed to install the plug ... 14.0 ± 2.0 N·m (10.00 ± 1.00 lb ft)
(5) Torque for the bolts ... 8.0 ± 1.0 N·m (70.00 ± 9.00 lb in)
(6) Torque for the housing assembly ... 14.0 ± 2.0 N·m (10.00 ± 1.00 lb ft)
(7) Torque that is needed to install the shuttle seat assembly ... 14.0 ± 2.0 N·m (10.00 ± 1.00 lb ft)
(8) Depth that is required to drive the ball below the sleeve ... 0.406 mm (0.0160 inch)
Caterpillar Information System:
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders Tire Inflation - Check
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Auxiliary)(Loader) (Mechanically Operated)
2001/10/29 The Torque Has Been Increased For The Bolts That Fasten The Stub Shafts To The Engine Cylinder Block {1237}
2001/10/22 A New Crankshaft Pulley is used on the Engine Crankshaft {1205}
3408E and 3412E Engines for Caterpillar Built Machines Diagnostic Codes
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0687 - FMI 02
CP-433C, CS-431C and CS-433C Paving Compactors Engine Starting
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0091 FMI 09 Position Sensor (Throttle) Abnormal Update - Test
PM-465 Cold Planer Water Spray System - Drain
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Hydraulic and Steering System Joystick Control (Backhoe)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Joystick Control (Backhoe)
3408E and 3412E Engines for Caterpillar Built Machines Alternator - Remove and Install
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Auxiliary)(Loader)(Pilot Operated)
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0168 FMI 01 Electrical System Voltage Below Normal Range - Test
2002/01/21 A New Quick Coupler is Required to Extend the Service Life of Dual Purpose Valves {6129, 7542}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Oil Filter (Power Train)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Pilot Valve (Joystick)
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Output Transfer Gears
735 Articulated Truck Power Train Rear Axle - Remove
TH210 and TH215 Telehandlers Power Train General Information
2001/11/26 Puller Holes Have Been Added to Gear Assemblies for the Transmission {3061}
2001/11/12 Corrections to Disassembly and Assembly , "Inlet and Exhaust Valve Guides - Remove and Install" {1104}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System System Power
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Fixed Axle and Oscillating Axle