Piston Pump (Brake) - Install
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 1 g00768519 - Install a new gasket (26) onto piston pump (7).
Show/hide table
Illustration 2 g00768508 - Attach a suitable nylon lifting sling around piston pump (7) and to a suitable hoist. Lift piston pump (7) into position. Align the spline on the shaft of the piston pump with the spline in the gear group at the front of the engine. Install two bolts (24) and two washers (25). The weight of piston pump (7) is
16 kg (35 lb) .Show/hide tableIllustration 3 g00768496 - Position block (20) with bracket (23) in order to install two bolts (21) and two washers (22). Do not tighten bolts (21). Refer to step 5.
Show/hide table
Illustration 4 g00768258 - Install two half clamps (18), four bolts (16) and four washers (17) in order to connect hose (19) to block (20). Tighten two bolts (21). Refer to step 4.
Show/hide table
Illustration 5 g00768250 Show/hide tableIllustration 6 g00768495 - Install two half clamps (5), four bolts (3) and four washers (4) in order to install tube (6) onto piston pump (7). Install bolt (12), two washers (13), clip (14) and nut (15) to secure tube (6). Connect hose (11) to tube (6) and tighten retaining nut (10). Connect hose (9) to piston pump (7) and tighten retaining nut (8).
Show/hide table
Illustration 7 g00768234 - Install breather hose (2) and tighten clamp (1).
End By:
- Install the crankcase guard. Refer to Disassembly and Assembly, RENR3446, "Crankcase Guard - Remove and Install".
- Lower the hood. Refer to Operation and Maintenance Manual, "Hood - Control".
Caterpillar Information System:
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Transmission Oil - Change
2001/01/29 Improvements have been made to the Steering Column {4338}
236, 246, 252 and 262 Skid Steer Loaders Machine Systems Piston Pump (Hydrostatic)
216 and 226 Skid Steer Loaders Machine Systems Piston Motor (Hydrostatic)
3524B Engines for 797 and 797B Off-Highway Trucks Cylinder Heads
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Steering Metering Pump - Disassemble
CP-663E, CS-663E and CS-683E Vibratory Compactors Vibratory System Relief Valve (Main) - Test and Adjust
2001/01/29 The Ladder Support for the Pipelayer Is Improved {7254}
2001/02/12 A New Fuel Ratio Control (FRC) is Available for Stanadyne Fuel Injection Pumps on some 3054 and 3056 Turbocharged Engines {1278}
797 Off-Highway Truck Filter and Screen Locations
CP-663E, CS-663E and CS-683E Vibratory Compactors Propel System Final Drive Planetary (Drum Propel)
330C Excavator Engine Crankcase Breather - Clean
CP-663E, CS-663E and CS-683E Paving Compactors Machine Systems Steering Hydraulic System
CP-663E, CS-663E and CS-683E Vibratory Compactors Propel System Machine Preparation for Troubleshooting
3500 Generator Set Engines Engine Oil Pressure - Test
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Transmission Oil Filter - Replace
CP-663E, CS-663E and CS-683E Vibratory Compactors Propel System Visual Inspection
CP-663E, CS-663E and CS-683E Paving Compactors Machine Systems Machine Preparation for Troubleshooting
2001/01/29 Rework Process for Exhaust Manifolds {1059}
2001/01/29 A New Guard Is Used on the Wiring Harness of Wheel Harvesters {7150}
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Transmission Oil Level - Check
216, 226 and 228 Skid Steer Loaders Engine Supplement Gear Motor (Fan) - Remove
CP-663E, CS-663E and CS-683E Vibratory Compactors Vibratory System Case Drain Flow for Piston Motor - Test and Adjust
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Steering Metering Pump - Assemble