Crankcase Guard (Rear) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7505 | Floor Jack | 1 |
B | 1U-7505 | Floor Jack | 1 |
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
- Open access door (1). Repeat this procedure for the opposite side.
Show/hide table
Illustration 2 g00751240 - Release two clamps (2).
Show/hide table
Illustration 3 g00751243 - Open fan assembly (3).
Show/hide table
Illustration 4 g00751247 - Remove cotter pin (4) and the pin. Disconnect the power actuator.
Show/hide table
Illustration 5 g00751252 - Place Tooling (A) under rear crankcase guard (6), as shown.
- Remove two bolts (5) and the washers.
Show/hide table
Illustration 6 g00751256 - Place Tooling (B) under rear crankcase guard (6), as shown.
- Remove bolt (7), the washer, and the pin. Repeat this process for the opposite side.
- Carefully lower Tooling (A) and Tooling (B) in order to lower rear crankcase guard (6). The weight of rear crankcase guard (6) is
205 kg (450 lb) .
Show/hide table
Illustration 1 | g00751239 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7505 | Floor Jack | 1 |
B | 1U-7505 | Floor Jack | 1 |
- Install Tooling (A) and Tooling (B) under rear crankcase guard (6), as shown. Carefully raise Tooling (A) and Tooling (B) in order to install rear crankcase guard (6). The weight of rear crankcase guard (6) is
205 kg (450 lb) . - Install two bolts (5) and the washers.
- Install pin (7), the bolt, and the washer. Repeat this procedure for the opposite side.
Show/hide table
Illustration 9 g00751247 - Connect the power actuator. Install the pin and cotter pin (4).
Show/hide table
Illustration 10 g00751243 - Close fan assembly (3).
Show/hide table
Illustration 11 g00751240 - Engage two clamps (2).
Show/hide table
Illustration 12 g00751239 - Close access door (1). Repeat this procedure for the opposite side.
Show/hide table
Illustration 7 | g00751252 |
Show/hide table
Illustration 8 | g00751256 |
End By:
- Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Lock Pin (Saw Bar Tensioner) - Inspect/Replace
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Lubrication System Oil Level - Check
3406E and 3456 Engines for Caterpillar Built Machines Fuel Transfer Pump
836G Landfill Compactor and 834G Wheel Dozer Power Train Crankcase Guard (Front) - Remove and Install
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Battery Disconnect Switch
836G Landfill Compactor and 834G Wheel Dozer Power Train Power Actuator (Crankcase Guard) - Remove and Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Saw Chain Lubrication System - Inspect/Adjust
793B Off-Highway Truck Power Train Torque Converter Inlet and Outlet Relief Valves
793B Off-Highway Truck Power Train Oil Cooler (Torque Converter and Front Brake Cooling)
424D, 428D and 438D Backhoe Loaders Brake Reservoir Oil Level - Check
2000/12/18 300 RPM Drive Kit for Rotors Can Improve Grain Quality {6934}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Stabilizer)
793B Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve (Torque Converter)
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Alternator - Remove and Install
424D, 428D and 438D Backhoe Loaders Belts - Inspect/Adjust/Replace
836G Landfill Compactor and 834G Wheel Dozer Power Train Power Actuator (Power Train Guard) - Remove and Install
793B Off-Highway Truck Power Train Gear Pump (Transmission and Brake Cooling)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Electric Starting Motor - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Cylinder Head Valves
2001/02/19 Special Instruction, REHS0911 , "Salvage Procedure for the Bore for the Idler Gear Bearing in the Output Transfer Gear Group" is now Available {3159}
793B Off-Highway Truck Power Train Oil Filter (Transmission Charging)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Cab - Install
G3304 and G3306 Engines Flywheel Housing - Inspect