Fuel Transfer Pump
Type 1
Show/hide table
 | |
| Illustration 1 | g00432018 |
(1) Inlet port
(2) Pressure regulating valve
Show/hide table
 | |
| Illustration 2 | g00432159 |
(3) Weep hole
(4) Outlet port
Show/hide table
 | |
| Illustration 3 | g00533385 |
Typical cover opposite the fuel transfer pump | |
(5) Nuts
- Tighten the nuts to the following torque. ... 30 ± 5 N·m (22 ± 4 lb ft)
Type 2
Show/hide table
 | |
| Illustration 4 | g00751180 |
(1) Inlet port
(2) Pressure regulating valve
Show/hide table
 | |
| Illustration 5 | g00751185 |
(3) Weep hole
(4) Outlet port
Show/hide table
| | |
| Illustration 6 | g00533385 |
Typical cover opposite the fuel transfer pump | |
(5) Nuts
- Tighten the nuts to the following torque. ... 30 ± 5 N·m (22 ± 4 lb ft)
Caterpillar Information System:
836G Landfill Compactor and 834G Wheel Dozer Power Train Crankcase Guard (Front) - Remove and Install
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Battery Disconnect Switch
836G Landfill Compactor and 834G Wheel Dozer Power Train Power Actuator (Crankcase Guard) - Remove and Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Saw Chain Lubrication System - Inspect/Adjust
793B Off-Highway Truck Power Train Torque Converter Inlet and Outlet Relief Valves
793B Off-Highway Truck Power Train Oil Cooler (Torque Converter and Front Brake Cooling)
424D, 428D and 438D Backhoe Loaders Brake Reservoir Oil Level - Check
2000/12/18 300 RPM Drive Kit for Rotors Can Improve Grain Quality {6934}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Stabilizer)
793B Off-Highway Truck Air System and Brakes Diverter Valve (Torque Converter and Front Brake Cooling)
3408 Engines for Caterpillar Built Machines Diagnostic Codes
793B Off-Highway Truck Power Train Oil Filter (Torque Converter)
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Lubrication System Oil Level - Check
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Lock Pin (Saw Bar Tensioner) - Inspect/Replace
836G Landfill Compactor and 834G Wheel Dozer Power Train Crankcase Guard (Rear) - Remove and Install
793B Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve (Torque Converter)
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Alternator - Remove and Install
424D, 428D and 438D Backhoe Loaders Belts - Inspect/Adjust/Replace
836G Landfill Compactor and 834G Wheel Dozer Power Train Power Actuator (Power Train Guard) - Remove and Install
793B Off-Highway Truck Power Train Gear Pump (Transmission and Brake Cooling)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Electric Starting Motor - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Cylinder Head Valves
2001/02/19 Special Instruction, REHS0911 , "Salvage Procedure for the Bore for the Idler Gear Bearing in the Output Transfer Gear Group" is now Available {3159}