Power Actuator (Crankcase Guard) - Remove and Install
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
- Remove two bolts (1) and the washers.
Show/hide table
Illustration 2 g00747933 - Open access door (2).
Show/hide table
Illustration 3 g00747908 Show/hide tableIllustration 4 g00747909 - Use toggle switch (3) in order to lower rear crankcase guard (4).
- Support the bottom of rear crankcase guard (4) with a suitable floor jack.
Show/hide table
Illustration 5 g00747910 - Open access door (5). Repeat this procedure for the opposite side.
Show/hide table
Illustration 6 g00747912 - Release two clamps (6).
Show/hide table
Illustration 7 g00747913 - Open fan assembly (7).
Show/hide table
Illustration 8 g00751150 - Remove cotter pin (8) and the pin.
Show/hide table
Illustration 9 g00751152 - Remove cotter pin (9) and the pin.
- Cut two wire ties (12) and disconnect electrical connector (10).
- Carefully remove power actuator (11).
Show/hide table
Illustration 1 | g00747907 |
- Carefully install power actuator (11).
- Install the pin and cotter pin (9).
- Connect electrical connector (10) and install two wire ties (12).
Show/hide table
Illustration 11 g00751150 - Install the pin and cotter pin (8).
Show/hide table
Illustration 12 g00747913 - Close fan assembly (7).
Show/hide table
Illustration 13 g00747912 - Engage two clamps (6).
Show/hide table
Illustration 14 g00747910 - Close access door (5). Repeat this procedure for the opposite side.
Show/hide table
Illustration 15 g00747908 Show/hide tableIllustration 16 g00747909 - Use toggle switch (3) in order to raise rear crankcase guard (4).
Show/hide table
Illustration 17 g00747933 - Close access door (2).
Show/hide table
Illustration 18 g00747907 - Install two bolts (1) and the washers.
Show/hide table
Illustration 10 | g00751152 |
End By:
- Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Saw Chain Lubrication System - Inspect/Adjust
793B Off-Highway Truck Power Train Torque Converter Inlet and Outlet Relief Valves
793B Off-Highway Truck Power Train Oil Cooler (Torque Converter and Front Brake Cooling)
424D, 428D and 438D Backhoe Loaders Brake Reservoir Oil Level - Check
2000/12/18 300 RPM Drive Kit for Rotors Can Improve Grain Quality {6934}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Stabilizer)
793B Off-Highway Truck Air System and Brakes Diverter Valve (Torque Converter and Front Brake Cooling)
3408 Engines for Caterpillar Built Machines Diagnostic Codes
793B Off-Highway Truck Power Train Oil Filter (Torque Converter)
836G Landfill Compactor and 834G Wheel Dozer Power Train Drive Shaft (Center) - Remove and Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Saw Pivot Bearing - Lubricate
836G Landfill Compactor and 834G Wheel Dozer Power Train Torque Converter - Install
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Battery Disconnect Switch
836G Landfill Compactor and 834G Wheel Dozer Power Train Crankcase Guard (Front) - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Fuel Transfer Pump
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Lubrication System Oil Level - Check
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Lock Pin (Saw Bar Tensioner) - Inspect/Replace
836G Landfill Compactor and 834G Wheel Dozer Power Train Crankcase Guard (Rear) - Remove and Install
793B Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve (Torque Converter)
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Alternator - Remove and Install
424D, 428D and 438D Backhoe Loaders Belts - Inspect/Adjust/Replace
836G Landfill Compactor and 834G Wheel Dozer Power Train Power Actuator (Power Train Guard) - Remove and Install
793B Off-Highway Truck Power Train Gear Pump (Transmission and Brake Cooling)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head