A Gas Spring for the Hood is Available {7251}
- Load Haul Dump (LHD):
- R1700 (PIN: 4LZ)
Reference: Maintenance Manual, RENR4700 (1DE0603), "Machine Repairs & Welding Procedures".
Description of Change: A gas spring for the hood is now available. The addition of a gas spring will assist in raising the hood in order to access the engine.
Adaptable To: The 160-6154 Gas Spring is adaptable to PIN: R1700-127
and Up by using the following procedure.
Show/hide table
Required Parts     | |||
Item     | Qty     | Part Number     | Description     |
1     | 1     | 9EP5597     | Mounting Block     |
2     | 1     | 5C-7261     | Nut     |
3     | 1     | 8T-4224     | Hard Washer     |
4     | 1     | 9EP5598     | Mounting Plate     |
5     | 1     | 160-6154     | Gas Spring     |
Procedure
- Weld the 9EP5597 Mounting Block (1) into the position that is shown in Illustration 1. Refer to Maintenance Manual, RENR4700 (1DE0603), "Machine Repairs & Welding Procedures".
Show/hide table
Illustration 1 | g00744005 |
Inside view of the rear frame (1) 9EP5597 Mounting Block (A) 221 mm (8.70 inch) (B) 58 mm (2.28 inch) |
- Weld the 9EP5598 Mounting Plate (4) to the hood (6). Refer to Maintenance Manual, RENR4700 (1DE0603), "Machine Repairs & Welding Procedures".
Show/hide table
Illustration 2 | g00744006 |
(1) 9EP5597 Mounting Block (2) 5C-7261 Nut (3) 8T-4224 Hard Washer (4) 9EP5598 Mounting Plate (5) 160-6154 Gas Spring (6) Hood (D) 275 mm (10.82 inch) |
- Connect the 160-6154 Gas Spring (5) to the 9EP5598 Mounting Plate (4) by using the 8T-4224 Hard Washer and the 5C-7261 Nut (2) .
- Connect the lower section of the 160-6154 Gas Spring (5) to the 9EP5597 Mounting Block (1) .
Caterpillar Information System:
2000/10/02 Installation of Larger Lower Lift Arm Bearings Improves Bucket Pin and Bearing Service Life {6107}
2000/10/02 An Improved 152-8346 Solenoid Valve Group is Available {5479}
2000/10/02 An Improved 152-8339 Solenoid Valve Group is Available {5479}
3114, 3116, and 3126 Engines for Caterpillar Built Machines Governor - Remove
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader Injector Solenoid Circuit - Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Governor - Install
247, 257, 267, 277 and 287 Multi Terrain Loaders and 216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1190 - FMI 04
RM-250C Reclaimer Mixer Machine Operation Information
797 Off-Highway Truck Air System Air Compressor - Check
725 and 730 Articulated Trucks Secondary Steering - Test
Caterpillar Monitoring System MID 030 - CID 0096 - FMI 03
2000/10/23 A New Deflector Has Been Added to the Mixing Chamber {6635}
2000/10/02 Improved Lower Lift Arm Bearings are Available {6107}
Caterpillar Monitoring System MID 030 - CID 0096 - FMI 08
Caterpillar Monitoring System MID 030 - CID 0100 - FMI 08
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-1050B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-245C Asphalt Pavers Propel System Piston Motor (Propel)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pump - Test and Adjust
AP-1050B and BG-245C Asphalt Pavers Propel Electronic Control Module
3126 Truck Engine Military Rocker Shaft - Disassemble
3406E and 3456 Engines for Caterpillar Built Machines Piston and Rings
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-1050B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-245C Asphalt Pavers Propel System Final Drive Planetary
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-1050B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-245C Asphalt Pavers Propel System Propel Hydraulic System
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist System
RM-250C Reclaimer Mixer Rotor Elevation