Governor - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 136-4149     | 调速器钳 (1)     | 1     |
B     | 128-8827     | 销 (1)     | 1     |
1U-7523 | 销导向器 (1)     | 1     |
Show/hide table
( 1 ) | 该工具属于 128-8822 调速器工具总成 。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有关调速器的更详细信息,请参阅维修手册, SENR6454, "3114、3116 和 3126 发动机调速器"。 维修手册, SENR6454 要求使用 1U-7326 调速器标定试验台 。 有关调速器部件的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8434, "3100 调速器检查和概述(机械调速器总成,用于配备机械式单体喷油器(MUI)的 3114、3116 和 3126 发动机)"。
- 将润滑剂涂在新的 O 形密封圈 (1) 上。 将新的 O 形密封圈 (1) 安装在缸盖中。
Show/hide table
图 1 | g00673178 |
- 将润滑剂涂在新的 O 形密封圈 (2) 上。 将新的 O 形密封圈 (2) 安装在管组件 (5) 上。
Show/hide table
图 2 | g00672733 |
- 将 O 形密封圈和管组件 (5) 安装在缸盖中。
Show/hide table
图 3 | g00672742 |
- 将润滑剂涂在新的 O 形密封圈 (3) 上。 将新的 O 形密封圈 (3) 安装在调速器上。
Show/hide table
图 4 | g00673180 |
- 将调速器在发动机上正确就位。
Show/hide table
图 5 | g00673182 |
- 安装将调速器固定到位的垫圈和螺栓 (7) 。
Show/hide table
图 6 | g00613563 |
- 将 U 形夹销 (6) 安装在工具 (B) 中。
Show/hide table
图 7 | g00672755 |
- 使用工具 (B) 安装 U 形夹销 (6) 和夹子。
Show/hide table
图 8 | g00672752 |
- 检查燃油设置调整情况。 请参阅测试和调整, SENR5118。
- 使用工具 (A) 将管组件 (5) 滑到调速器内。
Show/hide table
图 9 | g00655975 |
- 安装夹子 (4) 。
Show/hide table
图 10 | g00613071 |
- 安装机油管组件 (1) 。 安装管组件 (2) 和空燃比控制管组件 (3) ,如有配备。 塞住并盖住所有接头。
Show/hide table
图 11 | g00613041 |
- 安装调速器控制电缆。
End By: 安装燃油切断电磁阀。 请参阅 拆解和组装, "燃油切断电磁阀 - 拆卸和安装"。
Caterpillar Information System:
247, 257, 267, 277 and 287 Multi Terrain Loaders and 216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1190 - FMI 04
RM-250C Reclaimer Mixer Machine Operation Information
797 Off-Highway Truck Air System Air Compressor - Check
725 and 730 Articulated Trucks Secondary Steering - Test
Caterpillar Monitoring System MID 030 - CID 0096 - FMI 03
2000/10/23 A New Deflector Has Been Added to the Mixing Chamber {6635}
2000/10/23 Holes Have Been Added to the Rotor Hood in order to Reduce Buildup of Material {6635}
2000/10/23 Improvements have been made to the Mixing Chamber of the Rotor Hood {5632, 5634, 6635}
2000/10/23 The Supply Hose for the Rotor Brake Line has been Rerouted {4257, 5056}
2000/10/30 New Lines Group for Lubrication of the Rotor Bearing {5057, 5608}
CP-663E, CS-663E and CS-683E Vibratory Compactors Battery or Battery Cable - Replace
CP-663E, CS-663E and CS-683E Vibratory Compactors Battery - Clean/Check
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader Injector Solenoid Circuit - Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Governor - Remove
2000/10/02 An Improved 152-8339 Solenoid Valve Group is Available {5479}
2000/10/02 An Improved 152-8346 Solenoid Valve Group is Available {5479}
2000/10/02 Installation of Larger Lower Lift Arm Bearings Improves Bucket Pin and Bearing Service Life {6107}
2000/10/02 A Gas Spring for the Hood is Available {7251}
2000/10/02 Improved Lower Lift Arm Bearings are Available {6107}
Caterpillar Monitoring System MID 030 - CID 0096 - FMI 08
Caterpillar Monitoring System MID 030 - CID 0100 - FMI 08
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-1050B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-245C Asphalt Pavers Propel System Piston Motor (Propel)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Pump - Test and Adjust
AP-1050B and BG-245C Asphalt Pavers Propel Electronic Control Module