Quick Coupler - Install
Installation Procedure
- Prior to installation, apply 5P-0960 Molybdenum Grease to all pin bores.
- Fasten a hoist and suitable lifting slings to quick coupler (3). The weight of the quick coupler is 200 kg (440 lb).
- Use a hoist to install coupler assembly (3) .
- Install the shims and two upper pin assemblies (4) .
Show/hide table
Illustration 1 | g00739948 |
Typical Example IT38G Integrated Toolcarrier |
- Install two lower pin assemblies (5) .
- Remove the cribbing that was used to support tilt lever (2). Remove the hoist and suitable lifting slings from quick coupler (3) .
Show/hide table
Illustration 2 | g00478841 |
Typical Example IT38G Integrated Toolcarrier |
- Connect two hydraulic hose assemblies (1) .
Show/hide table
Illustration 3 | g00739944 |
938G Wheel Loader |
Show/hide table
Illustration 4 | g00479232 |
IT38G Integrated Toolcarrier |
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
2000/06/26 Proper Gear Installation Improves Service Life {5058}
3054B Engine for Caterpillar Built Machines Fuel System Pressure - Test
2000/08/21 Correction to Testing and Adjusting , "Gear Pump (Hoist) - Test and Adjust and Relief Valve (Hoist Raise) - Test and Adjust" {5073, 5073, 5083, 5083, 5136, 5136}
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
2000/08/21 Correction to Disassembly and Assembly , "Differential and Bevel Gear - Assemble" {3256, 3258}
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Check Valve (Pilot)
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders Extendable Stick Pads - Inspect/Replace - If Equipped
PF-300B and PS-300B Pneumatic Compactors Propel System General Information
416C, 426C, 428C, 436C and 438C Backhoe Loaders Parking
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Install
420D and 430D Backhoe Loaders Engine Oil and Filter - Change
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Wheel and Tire
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Pressure Control Valve - Shift Valve
424D, 428D and 438D Backhoe Loaders Final Drive Oil (Front) - Change
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Drum Drive
424D, 428D and 438D Backhoe Loaders Final Drive Oil Level (Front) - Check
420D and 430D Backhoe Loaders Fuel System Water Separator - Drain
424D, 428D and 438D Backhoe Loaders Fuses - Replace
420D and 430D Backhoe Loaders Hydraulic System Oil Filter - Replace
TH103 Telehandler Compensating Cylinder Bearing - Lubricate
TH103 Telehandler Cooling System Coolant Level - Check
TH103 Telehandler Engine Air Filter Primary Element - Clean/Replace
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Gear Pump (Ejector)