Hydraulic System Oil Filter - Replace
Show/hide table
Illustration 1 | g00723507 |
- Pull the hood release lever (1) in order to open the engine access door (2) on the top of the machine.
Show/hide table
Illustration 2 g00724530 - Remove the hydraulic tank filler cap that is located under the access panel on the top of the engine compartment.
Show/hide table
Illustration 3 g00724532 - The hydraulic oil filter is located on the left side of the machine.
Show/hide table
Illustration 4 g00290851 - Remove the filter element with a strap type wrench.
- Clean the filter element mounting base. Remove any part of the filter element gasket that remains on the filter element mounting base.
- Apply a light coat of oil to the gasket of the new filter element.
- Install the new filter element by hand. When the gasket contacts the filter element mounting base, tighten the filter element for an additional three quarters of a turn.
- Remove the hydraulic tank breather. Replace the old breather with a new breather.
Show/hide table
Illustration 5 g00724596 - Maintain the hydraulic oil level in the sight gauge between the "MIN" mark and the "MAX" mark. Add oil, if necessary.
- Inspect the gasket on the hydraulic tank filler cap for damage. Replace the gasket, if necessary.
- Install the hydraulic tank filler cap.
- Close the access door.
Caterpillar Information System:
424D, 428D and 438D Backhoe Loaders Fuses - Replace
420D and 430D Backhoe Loaders Fuel System Water Separator - Drain
424D, 428D and 438D Backhoe Loaders Final Drive Oil Level (Front) - Check
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Drum Drive
424D, 428D and 438D Backhoe Loaders Final Drive Oil (Front) - Change
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Pressure Control Valve - Shift Valve
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Wheel and Tire
938G Wheel Loader and IT38G Integrated Toolcarrier Machine Systems Quick Coupler - Install
2000/06/26 Proper Gear Installation Improves Service Life {5058}
3054B Engine for Caterpillar Built Machines Fuel System Pressure - Test
2000/08/21 Correction to Testing and Adjusting , "Gear Pump (Hoist) - Test and Adjust and Relief Valve (Hoist Raise) - Test and Adjust" {5073, 5073, 5083, 5083, 5136, 5136}
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
TH103 Telehandler Compensating Cylinder Bearing - Lubricate
TH103 Telehandler Cooling System Coolant Level - Check
TH103 Telehandler Engine Air Filter Primary Element - Clean/Replace
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Gear Pump (Ejector)
2001/02/12 A New Spacer Ring has been Added to the Air Cleaner Group {1051}
TH103 Telehandler Engine Air Filter Service Indicator - Inspect
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders Loader Bucket, Cylinder, and Linkage Bearings - Lubricate
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Air Control Valve (Retarder)
TH103 Telehandler Engine Oil and Filter - Change
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders Parking Brake - Check/Adjust
420D and 430D Backhoe Loaders Cab Door
420D and 430D Backhoe Loaders Radiator Core - Clean