Water Pump - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 1P-1861 | 挡圈钳 | 1 |
D | 125-9793 | 密封导套 | 1 |
E | 183-4028 | 密封导套 | 1 |
F | 6V-2012 | 深度千分尺 | 1 |
G | 169-5464 | 快速固化底漆 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (G) 清洁轴组件和壳体内的沉孔。
- 使用 (D) 将油封 (2) 安装到水泵壳体中。 安装油封时让零件号朝向壳体。 确保油封与壳体平齐。 请勿润滑密封。
- 将内轴承 (5) 安装在轴组件 (8) 上。
- 将轴组件 (8) 安装到水泵壳体 (9) 中。
- 使用工具 (B) 安装挡圈 (7)。
- 使用工具 (E) 和合适的压具将水封 (10) 安装到轴组件 (8) 上。 安装水封时让零件号朝上。 确保水封严密地置于壳体上。 请勿润滑密封。
- 使用合适的夹具将叶轮 (11) 安装到轴组件 (8) 上。 叶轮应当与轴组件的顶部平齐。
- 使用适当的压具安装齿轮 (6)。 将齿轮安装到
29.3 mm (1.15 inch) 的高度。 使用工具 (F) 来测量尺寸 "A"。 - 安装轴承 (5)。 确保轴承与齿轮平齐。
- 安装六角垫圈 (1) 和内六角头螺栓 (4)。
- 安装新密封垫和盖子。 拧紧螺栓 (3) 至扭矩为
18 ± 3 N·m (13 ± 2 lb ft) 。 - 安装将水泵与散热器相连的新密封垫和弯头组件。 安装将水泵与机油冷却器相连的新密封垫和弯头组件。
Show/hide table
图 1 | g01020687 |
Show/hide table
图 2 | g01020747 |
结束:
- 安装水泵。 请参阅拆解和组装, "水泵 - 安装"。
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Install
420D and 430D Backhoe Loaders Engine Oil and Filter - Change
420D and 430D Backhoe Loaders Engine Oil Level - Check
416D Backhoe Loader Engine Air Filter Service Indicator - Inspect
2006/08/21 Replacement Instructions for the Oil Level Gauge on the Brake, Steering and Hoist Tank {5056, 7450}
988G Wheel Loader Electrohydraulic System Pilot Control Actuator Pressure - Check
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Air Tank (Parking and Secondary Brake)
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Remove
IT28G Integrated Toolcarrier and 928G Wheel Loader Brake and Fan Drive System Service Brakes
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader E190 Engine Overspeed Warning
3054B Engine for Caterpillar Built Machines Fuel System - Prime
2000/07/24 Change to Operation and Maintenance Manuals for Machine Towing {3203, 7000}
416C, 426C, 428C, 436C and 438C Backhoe Loaders Parking
PF-300B and PS-300B Pneumatic Compactors Propel System General Information
416D, 420D, 424D, 428D, 430D, 432D and 442D Backhoe Loaders Extendable Stick Pads - Inspect/Replace - If Equipped
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Check Valve (Pilot)
2000/08/21 Correction to Disassembly and Assembly , "Differential and Bevel Gear - Assemble" {3256, 3258}
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
2000/08/21 Correction to Testing and Adjusting , "Gear Pump (Hoist) - Test and Adjust and Relief Valve (Hoist Raise) - Test and Adjust" {5073, 5073, 5083, 5083, 5136, 5136}
3054B Engine for Caterpillar Built Machines Fuel System Pressure - Test
2000/06/26 Proper Gear Installation Improves Service Life {5058}
938G Wheel Loader and IT38G Integrated Toolcarrier Machine Systems Quick Coupler - Install
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Wheel and Tire
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Pressure Control Valve - Shift Valve