Tire and Rim (Front) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-5809     | 液压泵     | 1     |
9U-7536 | 起吊台架(55 吨)     | 2     | |
B     | 8S-9906     | 棘轮拉拔器     | 1     |
开始:
- 安装车轮楔子。 请参阅拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
Show/hide table
按照建议的步骤拆卸和安装轮胎和/或车轮组件。 确保始终正确支撑住机器以及轮胎和/或车轮组件。 采用不正确的步骤拆卸和安装轮胎和/或车轮组件可造成人员伤亡。 |
- 将工具 (A) 放置在机器前部下方。 使用工具 (A) 提升机器前部,直到大部分重量离开前轮胎。
Show/hide table
图 1 | g01327719 |
- 拆卸固定轮胎和轮辋的 20 颗螺母 (1) 和垫圈 (2) 中的 18 颗。
注: 保留位于轮辋相对侧的两个螺母 (1) 和垫圈 (2) 。
Show/hide table
图 2 | g01326665 |
- 利用工具 (A) 提升机器,直到前轮胎离地。
- 将升降机放置在轮胎和轮辋下面。 采用工具 (B) 适当的吊索将轮胎和轮辋固定在升降机上,如图所示。
Show/hide table
图 3 | g00692308 |
Show/hide table
图 4 | g01327723 |
- 还可采用轮胎装卸机拆卸轮胎和轮辋,如图所示。
Show/hide table
图 5 | g00540960 |
- 从轮胎和轮辋拆卸两个剩余的螺母 (1) 和垫圈 (2) 。 拆卸轮胎和轮辋。 轮胎和轮毂的重量为 1950 kg (4300 lb)。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-5809     | 液压泵     | 1     |
9U-7536 | 起吊台架(55 吨)     | 2     | |
B     | 8S-9906     | 棘轮拉拔器     | 1     |
C     | 4C-5593     | 防粘结剂     | 1     |
Show/hide table
按照建议的步骤拆卸和安装轮胎和/或车轮组件。 确保始终正确支撑住机器以及轮胎和/或车轮组件。 采用不正确的步骤拆卸和安装轮胎和/或车轮组件可造成人员伤亡。 |
- 将升降机放置在轮胎和轮辋下面。 使用工具 (B) 适当的吊索将轮胎和轮辋固定在升降机上,如图所示。
Show/hide table
图 6 | g00692308 |
Show/hide table
图 7 | g01327723 |
- 还可采用轮胎装卸机安装轮胎和轮辋,如图所示。
Show/hide table
图 8 | g00540960 |
- 放置轮胎和轮辋。 轮胎和轮辋的重量为 1950 kg (4300 lb)。 将工具 (C) 用到螺母 (1) 和两个垫圈 (2) 上。 安装两个垫圈 (2) 和两个螺母 (1) 。 从轮胎上拆下工具 (B) 和升降机。
- 将工具 (C) 用在其余的垫圈 (2) 和螺母 (1) 上。 安装垫圈 (2) 和螺母 (1) 。 拧紧螺母 (1) 至扭矩为 1210 ± 55 N·m (892 ± 41 lb ft)。
Show/hide table
图 9 | g01326665 |
- 使用工具 (A) 以便将机器前部降到地面上。
Show/hide table
图 10 | g00692251 |
- 拆下工具 (A) 和工具 (B) 。
End By: 取走车轮楔子。 请参阅 拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
Caterpillar Information System:
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Wheel Chock (Front and Rear) - Remove and Install
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Steering Tank - Install
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Piston Pump (Fan Drive)
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Axle (Rear)
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Steering Tank - Remove
D400E Series II Ejector Truck Transmission Control
776D and 777D Off-Highway Truck/Tractors Power Train Position Sensor (Pulled Unit Control)
2000/04/03 New Steering Shafts are Available {4301}
2000/03/27 Correction to Operation and Maintenance Manual for the Bucket/Fork Selector Control {5112, 5112}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Longitudinal Stability Indicator System Load Indicator Control
D400E Series II Ejector Truck Machine Operation Information
D400E Series II Ejector Truck Engine Starting
CB-535B Vibratory Compactor Propel System Piston Motor (Wheel Propel)
Installation Instructions for the 145-7099 Wedge Socket {5415, 5418} Installation Instructions for the 145-7099 Wedge Socket {5415, 5418}
2000/04/17 Guideline For Reusable Parts and Salvage Operations, SEBF8419, "Axle Housing and Final Drive Hub Salvage Procedure for 24H Motor Graders" Is Available {3260, 4054}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air Tank (Service Brake and Retarder) - Remove and Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Piston Pump (Axle Propel)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Suspension Cylinder Sensor - Troubleshoot
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Test
CB-534C and CB-634C Vibratory Compactors Propel System Piston Pump Servo Neutral - Adjust
988G Wheel Loader Power Train System Schematic
TH62, TH63, TH82, TH83 and TH103 Telehandlers Longitudinal Stability Indicator System Switch (Boom)
2000/04/03 Special Instruction, REHS0578, "Assembly Procedure for Large Off-Highway Truck Flat Floor Body Assembly" is Available {7258}
525B and 535B Wheel Skidders Power Train Axle Housing - Disassemble