Load Sense Manifold - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Position load sensing manifold (20) back to the original location. Connect hose assemblies (18) and (19) .
Show/hide table
 | |
| Illustration 1 | g00668073 |
- Connect hose assembly (17) .
Show/hide table
 | |
| Illustration 2 | g00668071 |
- Connect hose assemblies (14), (15), and (16) .
Show/hide table
 | |
| Illustration 3 | g00668070 |
- Connect hose assemblies (12) and (13) .
Show/hide table
 | |
| Illustration 4 | g00668069 |
- Remove two nuts (11), the washers, and the bolts.
Show/hide table
 | |
| Illustration 5 | g00668067 |
- Install three bolts (9), the washers, and cover (10) .
Show/hide table
 | |
| Illustration 6 | g00659599 |
Show/hide table
 | |
| Illustration 7 | g00659597 |
- Install five bolts (8), the washers, and cover (7) .
Show/hide table
 | |
| Illustration 8 | g00659596 |
- Install three bolts (6), the washers, and cover (5) .
Show/hide table
 | |
| Illustration 9 | g00657228 |
Show/hide table
 | |
| Illustration 10 | g00657227 |
- Install two bolts (4) and the washers from cover (5) .
- Use two people to install cover (2). Install the remaining bolts (3) and the washers.
Show/hide table
 | |
| Illustration 11 | g00657226 |
- Install two bolts (1), the washers, and the nuts.
- Fill the cooling system. Refer to Operation and Maintenance Manual, SEBU7160, "Hydraulic System Oil - Change" for the correct procedure.
Caterpillar Information System:
572R Pipelayer Machine Systems Load Sense Manifold - Remove
572R Pipelayer Machine Systems Counterweight Control Valve - Assemble
CB-535B Vibratory Compactor Steering System Solenoid Valve (Wheel Tilt)
2000/01/17 Needle Peen Procedure Added To Special Instruction For Truck Frame Superstructure Retrofit {7050, 7253}
554 and 574 Forwarders Power Train Accumulator (Transmission Gearbox)
CB-214D, CB-224D and CB-225D Vibratory Compactors Propel System General Information
554 and 574 Forwarders Power Train Gear Pump (Transmission Gearbox)
554 and 574 Forwarders Power Train Oil Filter (Transmission Gearbox)
D250E Series II and D300E Series II Articulated Trucks Brakes, Indicators and Gauges - Test
3114, 3116 and 3126 MUI Engine Governors Throttle Lever (Types IV, V, VI, VII, and Some III) - Remove
CB-535B Vibratory Compactor Steering System Offset Valve
572R Pipelayer Machine Systems Counterweight Control Valve - Disassemble
572R Pipelayer Machine Systems Load Sense Manifold - Disassemble
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0100 FMI 13 Engine Oil Pressure calibration required
572R Pipelayer Machine Systems Load Sense Manifold - Assemble
3508B Engine for D11R Track-Type Tractors MID 036 - CID 0800 - FMI 09 Unable to communicate with VIMS
572R Pipelayer Machine Systems Hook Winch Motor - Disassemble
572R Pipelayer Machine Systems Hook Winch Motor - Assemble
572R Pipelayer Machine Systems Winch Control Valve - Disassemble
572R Pipelayer Machine Systems Winch Control Valve - Assemble
CB-535B Vibratory Compactor Propel System Drive and Vibratory Drum
3412E Engine for Caterpillar Built Machines CID 0091 FMI 02 Incorrect Throttle Switch inputs
2000/02/14 New Liquid Level Indicator (Coolant) Is Now Available {7470}
924G and 924GZ Wheel Loaders Power Train Differential Pinion (Front) - Disassemble