Engine Oil Filter Base - Remove
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Loosen two hose clamps (3) that hold the coolant hoses to the oil cooler. Disconnect the coolant hoses from the oil cooler.
Show/hide table
 | |
| Illustration 1 | g00762421 |
- Remove engine oil filter (2) and discard engine oil filter (2). Use a new engine oil filter for reassembly.
- Remove four bolts (1) from the filter base.
- Remove engine oil filter base (4) from the cylinder block. Immediately cap all openings or plug all openings in order to prevent contamination.
Caterpillar Information System:
CB-535B Vibratory Compactor Drum Offset Control
CB-535B Vibratory Compactor Engine Water Pump - Inspect
CB-535B Vibratory Compactor Engine Valve Lash - Check
CB-535B Vibratory Compactor Engine Oil and Filter - Change
CB-535B Vibratory Compactor Engine Oil Sample - Obtain
CB-535B Vibratory Compactor Engine Oil Level - Check
1999/12/06 New Service Magazine Format {0374, 1000, 7000}
CB-535B Vibratory Compactor Engine Mounts - Inspect
2000/01/10 Oil Filler Cap is Now Attached with a Lanyard {1316}
CB-535B Vibratory Compactor Engine Crankcase Breather - Clean - Engine Crankcase Breather Hose
CB-535B Vibratory Compactor Engine Air Filter Service Indicator - Inspect
CB-535B Vibratory Compactor Engine Air Filter Secondary Element - Replace
3054B Industrial Engine Engine Oil Filter Base - Install
3054B Industrial Engine Engine Oil Filter Base - Disassemble
TH62, TH63, TH82 and TH83 Telehandlers Braking System Service Brake Air - Purge
1999/12/20 Change to Tightening Procedure for Cylinder Head Bolts in Specifications, RENR1217 and Specifications, SENR5182 {1100}
TH62, TH63, TH82 and TH83 Telehandlers Hydraulic System Towing Hitch System - If Equipped
2000/02/21 New Air Cleaner Support and Exhaust Tube Bracket Available for 24H Motor Grader, D10R Track-Type Tractor, and the 651E and 657E Wheel Tractor Scrapers {1051, 1061}
2000/01/03 Locations Where New Tube Assemblies Are Used {1274}
2000/02/07 New Procedure to Test DASA 280C on Excavators With the HH65 Harvester Head {7610, 7620}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0261 FMI 13 Engine Timing Calibration required
988G Wheel Loader Power Train NoSPIN Differential
554 and 574 Forwarders Power Train Oil Level Sensor (Power Train Oil Tank)
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0001 FMI 05 Cylinder #1 Injector open circuit