Holding Arm - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Note: The HH65 Harvester Head is shown in this procedure. Other harvester heads are similar.
- Install grease fitting (8) in holding arm (3) .
Show/hide table
Illustration 1 | g00393846 |
- Press upper bushing (7) and lower bushing (9) into holding arm (3) .
- Place bearing (10) on the harvester head.
- Place holding arm (3) on the harvester head.
- Partially insert pivot pin (4). Install bearing (6) on holding arm (3). Fully insert pivot pin (4) .
- Install nut (5). Tighten the set screw on nut (5) .
Show/hide table
Illustration 2 | g00463867 |
- Position holding arm (3) so the cylinder pivot point is over the hole in the harvester head. Move holding arm cylinder (1) into position on holding arm (3). Install pivot pin (2) in the rod end. Install the washer and the nut on pivot pin (2). Tighten the nut.
- Lubricate the holding arm and the holding arm cylinder. Use 1P-0808 Multipurpose Grease .
Caterpillar Information System:
776D and 777D Off-Highway Truck/Tractors Power Train Transmission Hydraulic System
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Remove
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Holding Arm - Remove
980G Wheel Loader Power Train Differential
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Throttle Position Sensor
539 Knuckleboom Loader Hydraulic System Swing Motor Case Drain Oil - Measure
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Preparation for Disassembly
CB-214D, CB-224D and CB-225D Vibratory Compactors Lifting and Tying Down the Machine
980G Wheel Loader Power Train Output Transfer Gears
572R Pipelayer Engine Supplement Fan Guard - Remove and Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Upper Roller - Remove and Install
CB-214D, CB-224D and CB-225D Vibratory Compactors Stopping the Machine
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder
12H, 140H and 160H Motor Graders Power Train Transmission Oil Cooler - Remove
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Holding Arm Cylinder - Remove
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder
784C, 785C, 785D, 789C, 789D, 793C, 793D, 797 and 797B Off-Highway Trucks VIMS™ and Truck Payload Measurement System (TPMS) Glossary of Terms
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension Cylinder (Front)
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Holding Arm Cylinder - Install
3056 Engine for Caterpillar Built Machines Fuel System
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Tilt Cylinder - Remove
572R Pipelayer Engine Supplement Water Pump - Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Tilt Cylinder - Install
572R Pipelayer Engine Supplement Water Pump - Remove