Engine Support - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-7505     | Transmission Jack     | 1     |
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Open the hood. Refer to Operation and Maintenance Manual, "Engine Compartment Hood - Raise".
- Support the bottom of the engine with Tool (A) .
Note: The fuel tank was removed for photographic reasons.
Show/hide table
Illustration 1 | g00567559 |
Show/hide table
Illustration 2 | g00567567 |
- Remove nut (6), washer (5), bolt (1) and the two plated washers from each rear engine mount (2) .
- Remove bolts (3), the washers and rear engine mount (2) from each side of the rear of the engine.
- Remove mount assembly (4) on each side of the frame.
- Remove nut (11), washer (12), bolt (9) and the two plated washers from each front engine mount (7) .
Note: The hoses from the valves were removed for photographic reasons.
Show/hide table
Illustration 3 | g00567564 |
Show/hide table
Illustration 4 | g00567565 |
- Remove bolts (8), the washers and front engine mount (7) from each side of the engine.
- Remove mount assembly (10) from each side of the frame.
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-7505     | Transmission Jack     | 1     |
Note: Check the mount assemblies for wear or damage. Use new replacement parts, if necessary.
- Use Tool (A) to support the engine.
- Install mount assembly (10) on each side of the frame.
Note: The hoses from the valves were removed for photographic reasons.
Show/hide table
Illustration 5 | g00567564 |
Show/hide table
Illustration 6 | g00567565 |
- Install front engine mount (7) on each side of the engine with the washers and bolts (8) .
- Install bolt (9), the two plated washers, washer (12) and nut (11) on each front engine mount (7) .
- Install mount assembly (4) on each side of the frame.
Note: The fuel tank was removed for photographic reasons.
Show/hide table
Illustration 7 | g00567559 |
Show/hide table
Illustration 8 | g00567567 |
- Install rear engine mount (2) on each side of the rear of the engine with the washers and bolts (3) .
- Install bolt (1), the two plated washers, washer (5) and nut (6) on each rear engine mount (2) .
- Remove Tool (A) .
- Close the hood. Refer to Operation and Maintenance Manual, "Engine Compartment Hood - Lower".
Caterpillar Information System:
AP-1050B and BG-245C Asphalt Pavers Turbocharger - Inspect
24H Motor Grader Hydraulic and Steering System Relief Valve (Steering Cylinder Crossover)
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Battery - Remove and Install
Retrofitting the 136-7822 Transmission Control for the 109-3664 Transmission Control {3065} Retrofitting the 136-7822 Transmission Control for the 109-3664 Transmission Control {3065}
784C and 785C Off-Highway Truck Power Train Transmission Planetary and Transfer Gears - Remove
3054 Engine for Caterpillar Built Machines Fuel Injection Pump - Remove - Type 2 Engines and 7BJ Engines
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Wiring Harness
3054 Engine for Caterpillar Built Machines Fuel Injection Pump - Install - Type 1 Engines and 9RM Engines
797 Off-Highway Truck Steering System Front Wheel
D350E Series II Articulated Truck Center Suspension Frame - Remove
784C and 785C Off-Highway Truck Power Train Gear Pump (Rear Axle Oil) - Assemble
988G Wheel Loader Power Train Transmission Hydraulic System
D350E Series II Articulated Truck Hoist Cylinder - Remove
D400E Series II Articulated Truck Front Suspension Cylinder - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Steering Control - Assemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Mode 11 - Three-Point Hitch Status and Calibration
554 Forwarder and 574 Forwarder Secondary Disconnect Switch
3054 Engine for Caterpillar Built Machines Fuel Injection Pump - Install - Type 2 Engines and 7BJ Engines
784C and 785C Off-Highway Truck Power Train Transmission Planetary and Transfer Gears - Install
D350E Series II Articulated Truck Hoist Cylinder - Install
CB-634C Vibratory Compactor Parking Brake Control
416C, 426C, 428C, 436C and 438C Backhoe Loaders Hydraulic and Steering System Load Control Valve (Lift)
24H Motor Grader Hydraulic and Steering System Unloading Valve (Secondary Steering)
CB-634C Vibratory Compactor Propel Control