Trunnion Support (Oscillating Axle, Front) - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1H-3107     | Push-Puller     | 1     |
6V-2078 | Stud     | 2     |
Start By:
- Remove the oscillating axle. Refer to Disassembly and Assembly, "Oscillating Axle (Rear) - Remove and Install" for the machine that is being serviced.
- Place the oscillating axle on wood blocks, as shown.
Show/hide table
Illustration 1 | g00517673 |
- Remove yoke (1) from the differential pinion shaft.
- Attach a hoist and suitable lifting slings to front trunnion support (2), as shown.
Show/hide table
Illustration 2 | g00517709 |
- Use Tooling (A) and the hoist to carefully remove front trunnion support (2). The weight of the front trunnion support is 68 kg (150 lb).
- Remove two O-ring seals (3) from front trunnion support (2) .
Show/hide table
Illustration 3 | g00517732 |
- Remove sleeve bearing (4) from the front trunnion support.
Note:
Show/hide table
Illustration 4 | g00517734 |
Show/hide table
Illustration 5 | g00517735 |
Note: Bearing sleeve (4) is retained in the bores of the front trunnion support. Pry one side of the sleeve bearing over the top of the other side at the diagonal separation, as shown. DO NOT use a press to remove the bearing sleeve.
Installation Procedure
- Install sleeve bearing (4) in the front trunnion support by overlapping the sides at the diagonal separation.
Show/hide table
Illustration 6 | g00517735 |
- Push sleeve bearing (4) into the counterbore of the front trunnion support. Make sure that one side of the sleeve bearing is flush with the other side at the diagonal separation.
Show/hide table
Illustration 7 | g00517734 |
- Install two O-ring seals (3) in front trunnion support (2) .
Show/hide table
Illustration 8 | g00517732 |
- Apply 5P-0960 Molybdenum Grease to the sleeve bearing and the O-ring seals.
- Attach a hoist and suitable lifting slings to front trunnion support (2) .
Show/hide table
Illustration 9 | g00517787 |
- Use the hoist to carefully install front trunnion support (2) on the oscillating axle. The weight of the front trunnion support is 68 kg (150 lb).
- Install yoke (1) on the differential pinion shaft.
Show/hide table
Illustration 10 | g00517673 |
End By: Install the oscillating axle. Refer to Disassembly and Assembly, "Oscillating Axle (Rear) - Remove and Install" for the machine that is being serviced.
Caterpillar Information System:
CB-534C and CB-634C Vibratory Compactors Steering System Metering Pump (Steering)
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Disassemble
IT28G Integrated Toolcarrier Maintenance Interval Schedule
784C and 785C Off-Highway Trucks Machine Systems Body and Canopy - Remove
784C and 785C Off-Highway Trucks Machine Systems Door Panel (Right) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Door Panel (Left) - Remove and Install
554 Forwarder and 574 Forwarder Changing Direction and Speed
824G , 825G and 826G Landfill Compactor Steering Frame Lock
3406E and 3456 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove
3406E On-Highway Engine Rocker Arm and Shaft - Install
784C and 785C Off-Highway Trucks Machine Systems Door Handle and Latch - Remove
824G , 825G and 826G Landfill Compactor Compactor Wheel Chopper Blades - Inspect/Replace
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Service Brake (Front Caliper)
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering System Pressure - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering System Pressure - Test
3524B Engines for Off-Highway Trucks Too Much Vibration
CB-534C and CB-634C Vibratory Compactors Steering System General Information
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Assemble
3406E On-Highway Engine Housing (Front) - Remove
3406E On-Highway Engine Housing (Front) - Install
3524B Engines for Off-Highway Trucks Too Much Valve Lash
824G , 825G and 826G Landfill Compactor Tilt Hood
D250E Series II and D300E Series II Articulated Trucks Power Train Differential and Bevel Gear (Front and Rear) - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0804 FMI 09 Interface Module (No. 4) Abnormal Update - Test