Flywheel - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
- 加热齿圈至最高温度
315°C599 (°F) 。 将齿圈安装在飞轮上。 放置齿圈,让零件号朝向曲轴。 让齿圈冷却。 使用软面锤来使齿圈坐落到飞轮的凸肩。Show/hide table图 1 g00513879 - 将工具 (A) 安装到飞轮上。 将适当的起吊设备固定到飞轮上。
- 将飞轮放在曲轴上的原始位置中。 对准飞轮和曲轴上的箭头。
- 将 7M-7456 固定胶涂抹在八个螺栓 (1) 的螺纹上。
- 安装八个螺栓 (1) 和垫圈。 均匀拧紧螺栓至扭矩为
300 ± 40 N·m (221 ± 30 lb ft) 。 - 检查飞轮跳动。 请参阅测试和调整, "基本区块"中的正确步骤。
Caterpillar Information System:
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Message Center Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
784C and 785C Off-Highway Trucks Machine Systems Power Converter (CAB) - Remove and Install
527 Track-Type Skidder Walk-Around Inspection
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Control Valve (Hoist)
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
824G , 825G and 826G Landfill Compactor Hydraulic Control Support
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install