VIMS Keypad Module - Remove and Install
- Remove six truss head screws (1) in order to separate instrument panel (2) from the front dash.
Show/hide table
Illustration 2 g00521653 - Disconnect wire harness (3) from the electronic keypad control at the electrical connection.
Show/hide table
Illustration 3 g00521654 - Disconnect lamp (4) from the electronic keypad control.
Show/hide table
Illustration 4 g00521647 - Remove four screws (5) in order to remove electronic keypad control (6).
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Show/hide table
Illustration 1 | g00520611 |
- Verify that all of the components of electronic keypad control (6) are clean and free of foreign material prior to installation.
- Inspect all of the components for wear and replace the components, if necessary.
- Use four screws (5) in order to install electronic keypad control (6).
Show/hide table
Illustration 6 g00521654 - Connect lamp (4) to the electronic keypad control.
Show/hide table
Illustration 7 g00521653 - Connect wire harness (3) to the electronic keypad control at the electrical connection.
Show/hide table
Illustration 8 g00520611 - Use six truss head screws (1) in order to install instrument panel (2) to the front dash.
Show/hide table
Illustration 5 | g00521647 |
Caterpillar Information System:
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Message Center Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
784C and 785C Off-Highway Trucks Machine Systems Power Converter (CAB) - Remove and Install
527 Track-Type Skidder Walk-Around Inspection
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Transmission Systems Hydraulic Component Operation
784C and 785C Off-Highway Trucks Machine Systems Power Converter (Radio) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Module (Intermittent Wiper) - Remove and Install
554 Forwarder and 574 Forwarder Service Brake Control
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3176C and 3196 Industrial Engines Flywheel - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove