Cylinder Head - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite Graphite 50 Anti-Seize | - |
B | 8T-2998 | Lubricant | 1 |
C | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Thoroughly clean the spacer plate and the bottom surface of the cylinder head. A new spacer plate gasket must be installed when the cylinder head is removed.
- Apply a thin film of clean engine oil to O-ring seal (26). Install O-ring seal (26).
Show/hide table
Illustration 2 g00632048 - Install a new spacer plate gasket (25).
- Install the spacer plate on the engine.
Show/hide table
Illustration 3 g00632047 - Apply a thin film of clean engine oil to O-ring seal (22). Install O-ring seal (22).
- Install water seals (23) dry.
- Install seal (24) in the spacer plate.
Show/hide table
Illustration 4 g00580833 - Install a new cylinder head gasket (21).
Show/hide table
Illustration 5 g00580812 - Attach a suitable lifting device to cylinder head (8). Carefully position cylinder head (8) on the spacer plate. The weight of the cylinder head is approximately
235 kg (518 lb) .Show/hide tableIllustration 6 g00513934 Note: The bolts that are Marked “X” are
216 mm (8.5 inch) long. The remainders of the bolts are194 mm (7.6 inch) in length. - Apply a small amount of Tooling (A) to the bolt threads and both sides of the washers. Install the cylinder head bolts. Tighten the cylinder head bolts, as follows.
- In a numerical sequence, tighten bolts 1 through 26 to a torque of
270 ± 15 N·m (200 ± 11 lb ft) . - In a numerical sequence, tighten bolts 1 through 26 to a torque of
450 ± 15 N·m (330 ± 11 lb ft) . - In a numerical sequence, again tighten bolts 1 through 26 to a torque of
450 ± 15 N·m (330 ± 11 lb ft) .
Show/hide tableIllustration 7 g00580810 - In a numerical sequence, tighten bolts 1 through 26 to a torque of
- Install spacers (17) and bolts (18) that fasten bracket (19) to the cylinder head.
Show/hide table
Illustration 8 g00580808 - Connect the harness assembly to sensor (14), sensor (15), and ground stud (16).
- Install the bolt and support clip (13) for the harness assembly.
Show/hide table
Illustration 9 g00580807 - Install hose assemblies (10). Install the bolt and clamp (9).
Note: If the engine is not equipped with an air compressor, skip Step 14.
- Connect hose assemblies (11) and hose assemblies (12) to the air compressor.
Show/hide table
Illustration 10 g00580805 - Connect hose assembly (7) to cylinder head (8).
Show/hide table
Illustration 11 g00576240 Show/hide tableIllustration 12 g00576839 - Install O-ring seals (5) and (6) in seal assembly (3). Lubricate seal (6) with Tooling (B).
- Assemble thrust plate (1) and seal assembly (3). Apply Tooling (C) to bolts (2). Hold the assembly in position and install bolts (2). Evenly tighten bolts (2) until seal assembly (3) and O-ring seal (5) are seated against the cylinder head.
Note: Be careful to ensure that O-ring seal (5) stays in the groove in seal assembly (3).
- Install adapter (4). Ensure that the dowel in adapter (4) engages the hole in the camshaft.
Show/hide table
Illustration 1 | g00632049 |
End By:
- Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
- Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
- Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
- Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
- Install the water temperature regulator. Refer to Disassembly and Assembly, "Water Temperature Regulator - Remove and Install".
Caterpillar Information System:
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Message Center Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
784C and 785C Off-Highway Trucks Machine Systems Power Converter (CAB) - Remove and Install
527 Track-Type Skidder Walk-Around Inspection
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Transmission Systems Hydraulic Component Operation
784C and 785C Off-Highway Trucks Machine Systems Power Converter (Radio) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Module (Intermittent Wiper) - Remove and Install
554 Forwarder and 574 Forwarder Service Brake Control
527 Track-Type Skidder Transmission Scavenge Screen - Clean
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3176C and 3196 Industrial Engines Flywheel - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test