Inlet and Exhaust Valves - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5S-1330     | 气门弹簧压缩器     | 1     |
B     | 8S-2263     | 弹簧测试仪     | 1     |
开始:
- 拆卸缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 安装工具 (A) 并压缩气门弹簧。 从气门 (1) 上拆下气门弹簧座 (2) 。
Show/hide table
图 1 | g01042281 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 小心地从气门 (1) 上卸下工具 (A) 。
- 拆下气门旋转器 (3) 。
- 从气门 (1) 上拆下外气门弹簧 (5) 和内气门弹簧 (4) 。
- 从气门导管上拆下垫圈 (6) 和气门。
- 用工具 (B) 检查一下气门弹簧(弹力)。 请参阅技术规格, "缸盖气门"。
- 检查进气门和排气门。 请参阅技术规格, "缸盖气门"。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5S-1330     | 气门弹簧压缩器     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用清洁的发动机机油润滑进气门和排气门。 将进气门和排气门安装到缸盖中。
- 确保垫圈 (6) 已安装到气门导管。
Show/hide table
图 2 | g01042281 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将内气门弹簧 (4) 和外气门弹簧 (5) 安装到气门 (1) 上。
- 将气门旋转器 (3) 安装到气门 (1) 上。
- 使用工具 (A) 压缩内气门弹簧 (4) 和外气门弹簧 (5) 。 将气门弹簧座 (2) 安装到气门 (1) 上。
- 小心拆掉工具 (A) 。 用软质材料包裹的锤子敲击气门,以便确保气门弹簧座 (2) 安装正确。
Show/hide table
当松开气门弹簧压缩器的时候,气门弹簧卡座会从气门中弹出。 保证气门弹簧卡座正确安装在气门推杆上。 为了防止造成人员伤害,在安装气门时,应远离气门弹簧卡座前方和气门弹簧。 |
End By: 安装缸盖。 请参阅 拆解和组装, "缸盖 - 安装"。
Caterpillar Information System:
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Industrial Engines Flywheel - Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Control Valve (Hoist)
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
824G , 825G and 826G Landfill Compactor Hydraulic Control Support
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
554 Forwarder and 574 Forwarder Direction and Speed Control
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Install
CB-534C and CB-634C Vibratory Compactors Steering System Steering Control
824G , 825G and 826G Landfill Compactor Mirror
CB-534C and CB-634C Vibratory Compactors Steering System Steering Pivot and Oscillation Assembly
527 Track-Type Skidder Hydraulic System Hydraulic Tank and Filter