Radiator - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。
- 利用所密封的润滑剂轻轻润滑所有 O 形密封圈。
注: 安装前检查散热器的状态。 清除可阻碍空气流过散热器芯组件的污垢或碎屑。
- 将工具 (A) 和适当的起吊设备连接到散热器 (15) 。 散热器 (15) 的重量约为 370 kg (815 lb)。
Show/hide table
图 1 | g00513936 |
- 将散热器 (15) 放置在机器内。
- 将挡板组件 (37) 安装到机架上。 将螺栓 (36) 安装到挡板组件 (37) 上。
Show/hide table
图 2 | g00513933 |
- 如果螺栓 (34) 已拆下,将螺栓 (34) 安装到机器每一侧的支架 (35) 上。
Show/hide table
图 3 | g00513932 |
散热器右前侧 |
Show/hide table
图 4 | g00513931 |
散热器左前侧 |
- 将盖 (33) 和螺栓安装到机器每一侧的支架上。
Show/hide table
图 5 | g00514073 |
- 将螺栓 (29) 和安装件组件 (30) 安装到散热器支架 (31) 上。
Show/hide table
图 6 | g00513929 |
散热器右侧 |
Show/hide table
图 7 | g00513927 |
散热器左侧 |
- 如果螺栓 (32) 已拆下,则安装螺栓 (32) 。
- 将托架 (28) 定位到散热器 (15) 上。 安装将托架 (28) 固定到散热器 (15) 上的螺栓 (27) 。
Show/hide table
图 8 | g00513911 |
- 将密封垫安装到螺塞接头 (26) 并将螺塞接头 (26) 和密封垫安装到散热器 (15) 上。 安装螺栓 (25) 。
Show/hide table
图 9 | g00513885 |
- 安装将软管 (24) 固定到散热器 (15) 上的夹子和螺栓 (23) 。
Show/hide table
图 10 | g00513878 |
- 安装将线束组件固定到散热器 (15) 的新扎带 (22) 。
Show/hide table
图 11 | g00513861 |
- 将软管 (21) 安装到散热器 (15) 上。 将卡箍 (20) 安装到软管 (21) 上。 将卡箍 (20) 拧紧至扭矩为 13 ± 1 N·m (115 ± 9 lb in)。
Show/hide table
图 12 | g00513823 |
- 将阀组件 (19) 和螺栓 (18) 安装到散热器上。
Show/hide table
图 13 | g00513817 |
- 将风扇护罩组件 (17) 定位到散热器上。 安装螺栓 (16) 。
Show/hide table
图 14 | g00513765 |
- 安装将线束组件 (14) 固定到散热器 (15) 上的新扎带 (13) 。
Show/hide table
图 15 | g00513761 |
- 安装新扎带 (12) 。
Show/hide table
图 16 | g00552215 |
- 连接线束组件 (11) 。
Show/hide table
图 17 | g00513757 |
- 将前大灯 (10) 定位到挡泥板上。 连接线束组件 (9) 。
Show/hide table
图 18 | g00513744 |
- 安装将前大灯固定到挡泥板上的螺栓 (8) 。 安装新扎带。
Show/hide table
图 19 | g00513721 |
- 对其余前大灯重复步骤 20 和 21。
- 将空调贮液器 (7) 定位到散热器上。
Show/hide table
图 20 | g00513707 |
- 安装将管 (6) 固定到散热器上的夹子和螺栓 (5) 。
- 由两人将冷凝器 (3) 定位到散热器上。
Show/hide table
图 21 | g00513659 |
- 将螺栓 (1) 和安装件安装到冷凝器 (3) 上。
- 在快速连接器处将软管组件 (4) 连接到干燥器上。
- 将夹子和螺栓 (2) 安装到散热器上。
- 重新加注散热器。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
End By:
- 安装曲轴箱防护罩。 请参阅 拆解和组装, "曲轴箱防护罩 - 拆卸和安装"。
- 安装罩(散热器)。 请参阅 拆解和组装, "罩(散热器)- 拆卸和安装"。
Caterpillar Information System:
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Message Center Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
784C and 785C Off-Highway Trucks Machine Systems Power Converter (CAB) - Remove and Install
527 Track-Type Skidder Walk-Around Inspection
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Transmission Systems Hydraulic Component Operation
784C and 785C Off-Highway Trucks Machine Systems Power Converter (Radio) - Remove and Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3176C and 3196 Industrial Engines Flywheel - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Control Valve (Hoist)
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust