Solenoid Valve (Automatic Lubrication) - Remove and Install
拆卸步骤
开始:
- 卸下驾驶室后盖。 请参考拆卸和组装, "盖(驾驶室后部)- 拆卸和安装"部分。
- 释放空气系统中的压力。 请参考拆卸和组装, "储气罐(制动器)- 排放"部分。
Show/hide table
为防止可能的人身伤害,在断开空气系统的任何部件前,释放空气箱压力。 |
- 从压力保护阀上拆下软管组件 (1) 。
注: 清洁度是一项重要的因素。 在执行拆卸操作之前,应彻底清洁部件外部。 这将有助于防止污垢进入内部机构。
注: 为便于安装,在所有软管、油管组件、导线线束上做好标记。 插好所有软管组件和油管组件。 这将有助于防止液体泄漏,并有助于防止污染物进入系统。
Show/hide table
图 1 | g00521497 |
- 从驾驶室侧壁的接头上拆下软管组件 (2) 。
Show/hide table
图 2 | g00521499 |
- 从电磁阀上的电气连接处拆下导线线束 (3) 。
Show/hide table
图 3 | g00521508 |
- 卸下两个螺栓 (4) ,以拆下电磁开关 (5) 。
Show/hide table
图 4 | g00521514 |
Show/hide table
图 5 | g00521516 |
- 从电磁阀 (5) 上卸下软管组件 (1) 。
- 从电磁阀 (5) 上卸下软管组件 (2) 。
安装步骤
- 安装之前,请确认电磁阀 (5) 的所有部件都清洁无异物。
Show/hide table
图 6 | g00521516 |
Show/hide table
图 7 | g00521514 |
- 检查所有部件是否磨损,必要时更换部件。
- 将软管组件 (1) 安装到电磁阀 (5) 上。
注: 安装之前,在螺纹接头和管接头的螺纹上涂抹 5P-3413 管密封胶 。
- 将软管组件 (2) 安装到电磁阀 (5) 上。
- 使用两个螺栓 (4) 安装电磁阀 (5) 。
- 在电气连接处将导线线束 (3) 连接到电磁阀上。
Show/hide table
图 8 | g00521508 |
- 将软管组件 (2) 连接到驾驶室侧壁的接头上。
Show/hide table
图 9 | g00521499 |
- 将软管组件 (1) 连接到压力保护阀上。
Show/hide table
图 10 | g00521497 |
- 为储气罐充入压缩空气。 有关正确的操作程序,请参考运行和维护手册, SEBU7173, "利用外部气源起动"。
End By:
- 安装驾驶室后盖。 请参考 拆卸和组装, "盖(驾驶室后部)- 拆卸和安装"部分。
- 取走止轮块。 请参考 拆卸和组装, "止轮块(前轮和后轮)- 拆卸和安装"部分。
Caterpillar Information System:
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Message Center Module - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
784C and 785C Off-Highway Trucks Machine Systems Power Converter (CAB) - Remove and Install
527 Track-Type Skidder Walk-Around Inspection
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Transmission Systems Hydraulic Component Operation
784C and 785C Off-Highway Trucks Machine Systems Power Converter (Radio) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Module (Intermittent Wiper) - Remove and Install
554 Forwarder and 574 Forwarder Service Brake Control
527 Track-Type Skidder Transmission Scavenge Screen - Clean
3406C Engines for Caterpillar Built Machines Service Meter
527 Track-Type Skidder Transmission Oil Level - Check
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3176C and 3196 Industrial Engines Flywheel - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test