Vibration Damper and Pulley - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (5/8 - 18 NF)     |
1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下风扇传动带。 请参阅操作和维护手册, "皮带 - 检查/调整/更换"。
- 从减振器和皮带轮组件上拆下顶部螺栓 (1) 。 将工具 (A) 安装到螺栓的位置。
Show/hide table
图 1 | g00514084 |
- 拆下剩余的螺栓 (1) 。
- 从曲轴上拆下减振器 (3) 。
- 从曲轴上拆下皮带轮 (2) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (5/8 - 18 NF)     |
1     |
B     | 4C-5593     | 防粘结剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
彻底接触粘滞减振器是否有漏油或外壳凹陷(损坏)的迹象。 这两个情况中的任何一个都可能导致重块与外壳相接触。 这样会影响粘滞减振器的操作。 |
- 将工具 (A) 安装到曲轴顶部的螺栓孔中。
Show/hide table
图 2 | g00514084 |
- 将皮带轮 (2) 和减振器 (3) 安装到曲轴上。
- 将工具 (B) 涂抹在螺栓 (1) 上。 安装螺栓 (1) 。
- 拆下工具 (A) 。 安装螺栓 (1) 来代替工具 (A) 。
- 安装风扇传动带。 请参阅操作和维护手册, "皮带 - 检查/调整/更换"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Industrial Engines Flywheel - Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems VIMS Message Center Module - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Control Valve (Hoist)
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
824G , 825G and 826G Landfill Compactor Hydraulic Control Support
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
554 Forwarder and 574 Forwarder Direction and Speed Control
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Install
CB-534C and CB-634C Vibratory Compactors Steering System Steering Control