Inlet and Exhaust Valve Guides - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6895     | 气门导管冲头     | 1     |
Show/hide table
( 1 ) | 9U-7530 发动机工具总成 的部分工具 |
开始:
- 拆下进气阀和排气阀。 请参阅拆解和组装, "进气阀与排气阀 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从气门导管 (2) 上拆下气门杆密封 (1) 。
Show/hide table
图 1 | g01003942 |
- 使用工具 (A) 和锤子从缸盖上拆下气门导管。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6895     | 气门导管冲头     | 1     |
B (1)     | 9U-6894     | 导向圈     | 1     |
Show/hide table
( 1 ) | 9U-7530 发动机工具总成 的部分工具 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 2 | g01003943 |
- 用清洁的发动机机油润滑气门导管的孔。
- 用工具 (A) 和工具 (B) 将气门导管 (2) 安装到缸盖中,如图所示。
注: 必须使用工具 (B) 将气门导管安装到正确高度。
从缸盖表面到气门导管顶部的高度 ... 35.00 ± 0.50 mm (1.378 ± 0.020 in)
注: 有关详细信息,请参阅规格缸盖, "气门"。
- 将气门杆密封 (1) 安装到气门导管上。
End By: 安装进气阀和排气阀。 请参阅 拆解和组装, "进气阀与排气阀 - 拆卸和安装"。
Caterpillar Information System:
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Remove
3176C and 3196 Industrial Engines Flywheel - Install
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Control Valve (Hoist)
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Radiator - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Component Descriptions
784C and 785C Off-Highway Trucks Machine Systems VIMS Keypad Module - Remove and Install
3406E On-Highway Engine Cylinder Head - Install
784C and 785C Off-Highway Trucks Machine Systems Speedometer and Tachometer Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Sensor (Air System) - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 03 Position Sensor (Neutralizer Pedal) Voltage Above Normal - Test
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 03 Position Sensor (Ripper) Voltage Above Normal - Test
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
773D Off-Highway Truck and 775D Quarry Truck Hydraulic System Control Valve (Hoist)
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
824G , 825G and 826G Landfill Compactor Hydraulic Control Support
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
554 Forwarder and 574 Forwarder Direction and Speed Control
D250E Series II and D300E Series II Articulated Trucks Power Train Tire and Rim - Install
CB-534C and CB-634C Vibratory Compactors Steering System Steering Control
824G , 825G and 826G Landfill Compactor Mirror