Water Spray Pump Flow - Test
Show/hide table
Sudden movement of the machine can cause injury to persons on or near the machine. To prevent possible injury, perform the procedure that follows before testing and adjusting the water spray system. |
Show/hide table
Personal injury or death can result from escaping fluid under pressure. Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated by a doctor familiar with this type of injury. Always use a board or cardboard when checking for a leak. |
Show/hide table
Tools Needed     | ||
5P0753     | Tubing     | 1     |
5P4402     | Connector     | 6     |
4C8688     | Flowmeter (0.1-2.0 gpm)     | 1     |
8T0848     | Pressure Gauge (0-58 psi)     | 1     |
1U7648     | Tube Cutter     | 1     |
9X0507     | Valve     | 1     |
- Do the following steps before you perform the following test:
- Activate the parking brake.
- Place the propel lever in NEUTRAL.
- Remove the water pump from the machine.
Show/hide table
Illustration 1 | g00595851 |
Water Pump (1) Tube. (2) Connector. (3) Flowmeter. (4) Pressure Gauge. (5) Valve. (6) Water bottle. (7) Pump. |
- A temporary water circuit will need to be built. Use 5P-0753 Tube for the water lines. Take the 5P-0753 Tube and cut the tube with the 1U-7648 Tube Cutter. Cut the tube to various lengths, as needed. Use the 5P-4402 Air Brake Connector to connect the tube to all the components in the test. Do the following steps in order to build the temporary water circuit.
- Cut the tube. The tube will supply the water from the water bottle (6) to the pump (7). Connect the tube to the inlet side of the pump (7) .
- Cut a tube. The tube will supply the water from the outlet for the pump (7) to the inlet for the flowmeter (3) .
- Cut a tube. The tube will supply the water from the outlet for the flowmeter (3) to the gauge (4) .
- Cut a tube. The tube will supply the water from valve (5) to the water bottle (6) .
- Reconnect the electrical connector to the pump (7) .
- Turn on the water spray system.
- Use valve (5) to regulate the flow and the pressure of the water from the pump (7) .
- Record the various readings of water flow and the pressures. Compare the results with the following table.
Show/hide table
Water Pump Test     | |
Pressure (psi)     | Output Flow (gpm)     |
10     | 1.8     |
20     | 1.5     |
30     | 1.1     |
40     | .65     |
42     | Pump cut-out     |
Caterpillar Information System:
793C Off-Highway Truck/Tractor Power Train Screen (Torque Converter) - Assemble
AP-1000B and BG-260C Asphalt Pavers Front Wheel Assist Control (FWA) - If Equipped
527 Track-Type Skidder Lifting and Tying Down the Machine
3408B and 3408C Industrial and Marine Engines Gear Group (Rear)
527 Track-Type Skidder Leaving the Machine
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Drive Shaft
793C Off-Highway Truck/Tractor Power Train Screen (Torque Converter) - Disassemble
793C Off-Highway Truck/Tractor Power Train Transmission Hydraulic Control - Assemble
784C and 785C Off-Highway Trucks Machine Systems Hoist Cylinder - Remove
793C Off-Highway Truck/Tractor Power Train Transmission Hydraulic Control - Disassemble
793C Off-Highway Truck/Tractor Power Train Transmission Hydraulic Control - Remove
824G , 825G and 826G Landfill Compactor Model View Illustrations
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Steering and Brake Manifold Valve - Assemble
3406C Engines for Caterpillar Built Machines Fan Drive
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Fixed Axle
793C Off-Highway Truck/Tractor Power Train Transfer Gears - Disassemble
793C Off-Highway Truck/Tractor Power Train Transfer Gears - Assemble
793C Off-Highway Truck/Tractor Power Train Transmission and Transfer Gears - Remove
793C Off-Highway Truck/Tractor Power Train Transmission Planetary - Disassemble
793C Off-Highway Truck/Tractor Power Train Transmission Planetary - Assemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle
784C and 785C Off-Highway Trucks Machine Systems Hoist Cylinder - Install
Installation Guide for Operator Platform and Operator Access Ladder{7253, 7254} Installation Guide for Operator Platform and Operator Access Ladder{7253, 7254}
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Loader Payload System (LPS) General Information