Front Suspension (Cylinder) - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 148-0357 | 支杆提升总成 | 1 |
2H-2157 | 螺栓 | 8 | |
1D-4635 | 螺栓 | 4 |
- 安装之前先核实前悬架油缸的所有部件清洁无异物。
- 检查所有部件是否磨损或损坏,必要时更换部件。
注: 以下程序对于机器两侧完全相同。 必要时,对机器的另一侧重复此程序。
Show/hide table图 1 g02437967 Show/hide table图 2 g02437964 - 仅当前悬架处于水平位置时才需要进行步骤 4 和 5 。
- 将合适的起吊设备套到前悬架油缸上。 将起吊设备固定到适当的起重机上。 将前悬架油缸提升至垂直位置。 拆下销和两个开口销 (9)。
- 定位工具 (A) 然后安装螺栓 (X)。
Show/hide table
图 3 g00509946 - 将定位销 (8) 和键 (7) 安装至机架组件。
Show/hide table
图 4 g02299755 Show/hide table图 5 g02438003 Show/hide table图 6 g01270711 - 使用工具 (A) 以放置前悬架油缸和车轴。 前悬架油缸和车桥的整体重量约为
1200 kg (2640 lb) 。 - 安装螺栓 (6)。 手动拧紧螺母和螺栓 (6)。 按交叉顺序拧紧螺母和螺栓 (6)。 拧紧螺母和 (6) 至扭矩为
945 ± 35 N·m (700 ± 26 lb ft) 。Show/hide table图 7 g00509931 - 连接线束组件 (5)。 定位接头,然后拧紧螺栓 (4)。
Show/hide table
图 8 g00509929 - 将适当的起吊设备套到转向臂 (2) 上。
- 将转向臂 (2) 放置到车轴上。 安装螺栓 (3)。
Show/hide table
图 9 g00509926 - 将软管组件 (1) 连接至液压夹钳行车制动器上。
Show/hide table
进行维修之前,应阅读悬挂油缸上的所有警告标签。
释放氮气压力之前,必须先将机器停在平稳的地面上。
释放所有氮气压力之前,切勿对悬挂油缸中的机油进行检查。
除非活塞杆完全缩回,且所有氮气压力都已排尽,否则请勿卸下悬挂油缸上的任何阀门、盖子或螺塞。
悬挂油缸充油、排放或测试和调整过程中,或者提升或降低机器时,不要靠近机器。
机器突然向上或向下移动可能会导致净空高度迅速改变。
忽视此警告可能会导致人身伤亡。
- 充压前悬架油缸。 请参阅测试和调整, "前悬架(油缸)- 排气和充油"。
Show/hide table
制动液压系统的机油中存在空气会造成人员伤亡。
系统中存在空气会影响制动器完全发挥作用,且机器上的车轮可能无法停止。
要使制动液压系统正常工作,其中的机油不得存在空气。
- 排出制动系统中的空气。 请参阅空气系统和制动系统操作、测试和调整, "制动系统空气 - 排气"。
结束:
- 安装轮胎和轮缘(前)。 请参阅拆解和组装, "轮胎和轮缘(前)- 拆卸和安装"。
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Assemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Remove
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Remove
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Caliper Service Brake - Install
773D Off-Highway Truck and 775D Quarry Truck Transfer Gears
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Off-Board Service Tool
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air Control Valve (Pulled Unit)
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Remove
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Glossary of Terms
773D Off-Highway Truck and 775D Quarry Truck Drive Shaft (Main)
D250E Series II and D300E Series II Articulated Trucks Power Train Accumulator (Retarder) - Remove
797 Off-Highway Truck Power Train Transmission Planetary - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Accumulator (Retarder) - Install
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Bucket and Implement Control
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Drive Shaft (Main)
988G Wheel Loader Power Train Parking Brake - Disassemble
527 Track-Type Skidder Power Train Steering and Brake Control Valve
527 Track-Type Skidder Windows - If Equipped
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic System
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Gear Pump (Pulled Unit Hydraulics and Rear Brake Cooling)