Front Suspension (Cylinder) - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 148-0357 | 支杆提升总成 | 1 |
1J-7370 | 螺栓 | 8 | |
1D-4635 | 螺栓 | 4 |
开始:
- 拆下轮胎和轮缘(前)。 请参阅拆解和组装, "轮胎和轮缘(前)- 拆卸和安装"。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
进行维修之前,应阅读悬挂油缸上的所有警告标签。 释放氮气压力之前,必须先将机器停在平稳的地面上。 释放所有氮气压力之前,切勿对悬挂油缸中的机油进行检查。 除非活塞杆完全缩回,且所有氮气压力都已排尽,否则请勿卸下悬挂油缸上的任何阀门、盖子或螺塞。 悬挂油缸充油、排放或测试和调整过程中,或者提升或降低机器时,不要靠近机器。 机器突然向上或向下移动可能会导致净空高度迅速改变。 忽视此警告可能会导致人身伤亡。 |
Show/hide table
悬架油缸突然移动可造成人员伤亡。 突然上下移动可导致您头部上方的间隙快速变化。 维修前,务必阅读悬架油缸上的所有警告标签。 在氮气压力完全消失前,不要检查悬架油缸内的油。 除非连杆完全收回且氮气压力完全释放,否则任何情况下都不要拆下油缸上的阀门、盖或螺塞。 测试或调整悬架油缸时,不要站在机器下面。 |
注: 以下程序对于机器两侧完全相同。 必要时,对机器的另一侧重复此程序。
- 排出系统中的氮气。 请参阅测试和调整, "前悬架(油缸)- 排气和充油"。
Show/hide table
图 1 g00509926 - 从液压夹钳行车制动器上断开软管组件 (1)。
Show/hide table
图 2 g00509929 - 将吊索绕在转向臂 (2) 上周围,如图所示。 将吊索固定到适当的举倾机构上。
- 从车轴上拆下螺栓 (3) 并降低转向臂 (2)。
Show/hide table
图 3 g00509931 - 松开螺栓 (4) 并拆下连接器。 断开线束组件 (5)。
Show/hide table
图 4 g02299755 - 如图所示,使用适当的升降机将工具 (A) 连接至轴。 使用工具 (A) 和合适的升降机支撑前悬架油缸和车轴的重量。
Show/hide table
图 5 g02438003 - 拆下螺栓 (6)。
- 将车价组件作为整体从前悬架油缸和车轴上拆下。 前悬架油缸和车桥作为一个整体的重量约为
1200 kg (2640 lb) 。Show/hide table图 6 g00509946 - 将键 (7) 和定位销 (8) 从机架组件上拆下。
注: 只有当前悬挂油缸需要水平放置时才要求以下步骤。
Show/hide table图 7 g02437964 - 将工具 (A) 放置在平整地面上。 拉出位于工具 (A) 上的两个开口销 (9) 和销。
- 将合适的起吊设备套到前悬架油缸上。 将起吊设备固定到适当的起重机上。 拆下位于工具 (A) 的基座两侧的八个螺栓 (X) 和垫圈。 从工具 (A) 的底座上拆下前悬架油缸和车轴。
Show/hide table
图 8 g02437967 - 将工具 (A)、前悬架油缸和车轴放置在工具 (A) 的底座上。 安装销和两个开口销 (9)。
- 将工具 (A)、前悬架油缸和车轴放置在工具 (A) 的底座上。 在将前悬架油缸置于水平位置前,应先将销和开口销 (9) 安装在工具 (A) 上。
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Remove
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Caliper Service Brake - Install
773D Off-Highway Truck and 775D Quarry Truck Transfer Gears
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Off-Board Service Tool
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air Control Valve (Pulled Unit)
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Remove
527 Track-Type Skidder Power Train Drive Shaft
527 Track-Type Skidder Power Train Bevel and Transfer Gears
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Assemble
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Glossary of Terms
773D Off-Highway Truck and 775D Quarry Truck Drive Shaft (Main)
D250E Series II and D300E Series II Articulated Trucks Power Train Accumulator (Retarder) - Remove
797 Off-Highway Truck Power Train Transmission Planetary - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Accumulator (Retarder) - Install
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Bucket and Implement Control
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Drive Shaft (Main)
988G Wheel Loader Power Train Parking Brake - Disassemble
527 Track-Type Skidder Power Train Steering and Brake Control Valve
527 Track-Type Skidder Windows - If Equipped