Service and Parking Brake (Rear) - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7574     | 连杆支架     | 2     |
B     | 138-7575     | 连杆支架     | 2     |
C     | 164-4622     | 卡箍组件     | 1     |
D     | 8S-1378     | 拆卸器、螺柱和重置     | 1     |
E     | 2P-5535     | 螺柱拆卸器组件     | 1     |
F     | 140-7642     | Duo-Cone 密封件安装器组件     | 1     |
G     |     | 1/2 x13 个顶出螺栓     | 2     |
开始:
- 拆卸后部行车制动器和停车制动器。 请参阅拆解和组装, "后部行车制动器和停车制动器 - 拆卸"。
- 如图所示,将行车制动器和停车制动器置于木块上。
Show/hide table
图 1 | g00508624 |
- 从制动器锚销上拆下螺栓 (1) 和硬垫圈。
- 力度均匀地松开螺母 (2) 。 将每个螺母松开一圈,然后操作下一个螺母,直到释放所有弹簧压力。
Show/hide table
图 2 | g00508649 |
Show/hide table
拆除螺母时,弹簧释放出的弹力会造成人身伤害。 弹力会在拆除螺母和制动销时释放。 匀力松开螺母,每次旋转一圈,以便释放弹簧弹力。 |
- 将工具 (A) 和适当的起吊设备连接在制动器锚销 (3) 上。 从拔梢锁紧双头螺柱上拆下螺母 (2) 。
Show/hide table
图 3 | g02029086 |
- 从环上拆下制动器锚销 (3) 。 制动器锚销 (3) 的重量约为 112 kg (247 lb)。
- 将制动器锚销 (3) 置于适当的作业表面上。 卸下工具 (A) 和适当的起吊设备。
- 将工具 (A) 和适当的起吊设备安装在制动器锚销 (3) 上。 如图所示,使用工具 (A) 和适当的起吊设备转动制动器锚销 (3) 。 制动器锚销 (3) 的重量约为 112 kg (247 lb)。
Show/hide table
图 4 | g02029089 |
Show/hide table
图 5 | g00508656 |
- 如图所示,将工具 (G) 装入活塞。 力度均匀地拧紧工具 (G) ,直到两个活塞之间约为 25.4 mm (1.00 in)。
- 将开口销 (6) 安装到弹簧导向装置 5 () 中的孔中。 开口销安装在活塞下面,从而在从活塞上拆下顶出螺钉时将弹簧导向装置 (5) 固定到位。
Show/hide table
图 6 | g00598821 |
- 对其余三个弹簧导向装置重复步骤 9。
- 从活塞上拆下工具 (G) 。
- 使用软面锤向下均匀敲击活塞,直到可以将销 (7) 从弹簧导向装置 (5) 上拆下。
Show/hide table
图 7 | g00508658 |
Show/hide table
图 8 | g00515918 |
- 对其余弹簧导向装置重复步骤 12。
- 将工具 (B) 和适当的起吊设备安装到活塞 (8) 上。 从制动器锚销上拆卸活塞 (8) 。 活塞 (8) 的重量大约为 42 kg (93 lb)。
Show/hide table
图 9 | g01035822 |
- 从活塞 (8) 上拆下密封圈 (9) 。
Show/hide table
图 10 | g00508662 |
- 将密封件和密封圈 (10) 从活塞 (8) 上拆下。
- 从活塞 (8) 上卸下密封圈 (11) 。
- 拆下螺母 (12) 。 将工具 (B) 和适当的起吊设备安装到活塞 (14) 上。 力度均匀地松开位于活塞 (14) 凸缘下的其余螺母。 继续松开下一个螺母前,将每个螺母松开一圈。
Show/hide table
图 11 | g00508663 |
Show/hide table
图 12 | g01041295 |
Show/hide table
拆卸活塞时,所释放的弹簧力可能会导致伤害。 拆卸螺母时,将会释放弹簧力。 力度均匀地松开螺母,一次松开一圈以释放弹簧力。 |
- 将活塞 (14) 和壳体 (13) 作为一个整体从制动器锚销 (3) 上拆下。 活塞 (14) 和壳体 (13) 的重量大约为 69 kg (152 lb)。
- 将壳体 (13) 置于木块上。 将壳体 (13) 与活塞 (14) 分离开。 活塞 (14) 的重量大约为 40 kg (88 lb)。 从活塞 (14) 上拆下工具 (B) 和相应的起吊设备。
Show/hide table
图 13 | g01035838 |
- 将密封件和密封圈 (15) 从壳体 (13) 上拆下。
Show/hide table
图 14 | g00508902 |
- 将密封件和密封圈 (16) 从壳体 (13) 上拆下。
- 使用工具 (C) 压缩弹簧 (17) 。 从弹簧导向装置 (5) 上拆下开口销 (6) 。
Show/hide table
图 15 | g00572198 |
Show/hide table
图 16 | g00515928 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 慢慢地释放弹簧 (17) 的张紧力。 拆下工具 (C) 。
- 从活塞上拆下弹簧导向装置 (5) 和弹簧 (17) 。
- 对其余的弹簧导向装置 (5) 重复步骤23至25。
- 将密封件 (18) 、弹簧 (19) 和弹簧 (20) 从制动器锚销 (3) 上拆下。 使用工具 (D) (图中未显示)拆卸九个拔梢锁紧双头螺柱 (22) 。
Show/hide table
图 17 | g00508941 |
注: 为了便于组装,在弹簧的位置处作识别标记。
- 使用工具 (E) (图中未显示)拆卸拔梢锁紧双头螺柱 (22) 。
- 将减震器组件 (23) 从环 (24) 上拆下。
Show/hide table
图 18 | g00508944 |
- 从环 (24) 上拆下摩擦盘 (25) 。
Show/hide table
图 19 | g00508967 |
- 从环 (24) 上拆下板 (26) 。
Show/hide table
图 20 | g00515930 |
- 对于其余八个摩擦盘和七个外板重复步骤 30 和 31。
- 将减震器组件 (27) 从环 (24) 上拆下。
Show/hide table
图 21 | g00515936 |
- 如图所示,将适当的起吊设备置于制动器毂 (28) 上。 将起吊设备固定到适当的起重机上。 从环 (24) 上拆下制动器毂 (28) 。 制动器毂 (28) 的重量约为 45 kg (99 lb)。
Show/hide table
图 22 | g02029094 |
- 从制动器毂 (28) 上卸下密封圈 (29) 。
Show/hide table
图 23 | g00515937 |
Show/hide table
图 24 | g00515938 |
- 使用工具 (F) 将 Duo-cone 密封件 (30) 从制动器毂 (28) 上拆下。
- 将工具 (A) 和适当的起吊设备连接到环 (24) 上。 拆下将板 (31) 固定至环 (24) 的螺栓 (32) (图中未显示)和硬垫圈。
Show/hide table
图 25 | g02029099 |
- 从板 (31) 上拆下 O 形密封圈 (24) 。 环 (24) 的重量约为 67 kg (148 lb)。
- 从环 (24) 上拆下 O 形密封圈 (33) 。
Show/hide table
图 26 | g00515940 |
- 使用工具 (D) 将拔梢锁紧双头螺柱 (34) 从板 (31) 上拆下。
Show/hide table
图 27 | g00508996 |
Caterpillar Information System:
784C and 785C Off-Highway Trucks Machine Systems Fuel Tank - Install
3306C Engines for Caterpillar Built Machines Crankshaft
527 Track-Type Skidder Warning Signs and Labels
527 Track-Type Skidder Power Train Transmission and Torque Converter Pump
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Diverter Valve
D250E Series II and D300E Series II Articulated Trucks Power Train Torque Converter - Disassemble
583R Pipelayer Power Train Transmission and Bevel Gears - Connect
583R Pipelayer Power Train Track Roller - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Sensor Signal Voltage - Test
3176C and 3196 Engines for Caterpillar Built Machines Electronic Control System Components
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Pulse Width Modulated (PWM) Sensor - Test
583R Pipelayer Power Train Track Roller - Remove
527 Track-Type Skidder Power Train Torque Converter
D250E Series II and D300E Series II Articulated Trucks Power Train Torque Converter and Retarder - Connect
773D Off-Highway Truck and 775D Quarry Truck Pressure Control Valve (Transmission)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Sensor Dynamic Test
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Automatic Retarder) - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Hydraulic Control Valve - Disassemble
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Manual Retarder) - Remove and Install
527 Track-Type Skidder Fire Prevention and Explosion Prevention
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Secondary Brake) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Service Brake) - Remove and Install
3406E On-Highway Engine Camshaft - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Metering Pump (Steering) - Assemble