Relief Valve (Torque Converter Outlet) - Assemble
组装步骤
注: 清洁度是一项重要的因素。 组装之前，应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上，从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏，则应使用新零件进行更换。
- 在滑阀组件 (11) 上将提升阀 (13) 、弹簧 (14) 和挡圈 (15) 安装到位。 安装挡圈 (16) 。
Show/hide table
 | |
| 图 1 | g01114650 |
Show/hide table
 |
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 将隔套 (12) 安装到滑阀组件 (11) 中。
- 将 O 形密封圈 (10) 和滑阀组件 (11) 安装到阀体 (1) 中。
注: 隔套 (12) 用于调整打开变矩器出口安全阀所需的压力。 有关正确步骤，请参阅正在维修机器的测试和调整。
Show/hide table
 | |
| 图 2 | g01083623 |
- 安装盖 (9) 和螺栓 (8) 。 将螺栓拧紧至扭矩为 48 ± 7 N·m (35 ± 5 lb ft)。
Show/hide table
 | |
| 图 3 | g01083622 |
- 将螺塞 (7) 和 O 形密封圈 (5) 安装在阀体 (1) 内。
Show/hide table
 | |
| 图 4 | g01083621 |
- 安装弹簧 (6) 。
- 安装盖 (4) 和螺栓 (3) 。 用 48 ± 7 N·m (35 ± 5 lb ft) 的扭矩拧紧螺栓 (3) 。
Show/hide table
 | |
| 图 5 | g00497897 |
Show/hide table
|
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 将 O 形密封圈 (2) 安装在阀体 (1) 外侧。
Show/hide table
 | |
| 图 6 | g00497895 |
End By: 安装变矩器出口安全阀。 请参阅 拆解和组装, "安全阀（变矩器出口）- 安装"。
Caterpillar Information System:
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Water Tank (Rear)
IT14G Integrated Toolcarrier and 914G Wheel Loader Engine Supplement Electric Starting Motor - Remove and Install
583R Pipelayer Machine Systems Bottom Guard - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Relay Valve (Air Start) - Remove and Install
966F Series II Wheel Loader Power Train Output Transfer Gears - Disassemble
980G Wheel Loader Power Train Relief Valve (Torque Converter Outlet) - Disassemble
3406E and 3456 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
980G Wheel Loader Power Train Relief Valve (Torque Converter Outlet) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Engine Supplement Alternator - Remove and Install
583R Pipelayer Power Train Track - Connect
583R Pipelayer Engine Supplement Water Pump - Assemble
CB-534C Vibratory Compactor Propel Control
572R Pipelayer Power Train Track - Disassemble
583R Pipelayer Machine Systems Implement Pump - Disassemble
583R Pipelayer Machine Systems Boom Sheave Block (Lower) - Remove
583R Pipelayer Machine Systems Hook Sheave Block (Upper) - Install
583R Pipelayer Machine Systems Implement Pump - Assemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Engine Supplement Water Separator - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0075 FMI 03 Temperature Sensor (Steering Oil) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0075 FMI 04 Temperature Sensor (Steering Oil) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0075 FMI 06 Temperature Sensor (Steering Oil) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0096 FMI 03 Level Sensor (Fuel) Voltage Above Normal - Test
784C and 785C Off-Highway Trucks Machine Systems Air Dryer - Remove and Install
966G Wheel Loader and 972G Wheel Loader Engine Supplement Piston Motor (Hydraulic Fan) - Disassemble