Hydraulic System Oil Filter, Strainer and Breather - Replace/Clean
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Park the machine on a level surface. Ensure that the parking brake is fully engaged. Lower the dump body and stop the engine.
Show/hide table
Illustration 1 | g00604735 |
Remove hydraulic tank cover (1).
Strainer
- Unlock padlock (2) on filler cap (3). Remove filler cap (3) slowly in order to relieve the hydraulic system pressure.
Show/hide table
Illustration 2 | g00604819 |
- Inspect filler cap gasket (4). If necessary, replace the filler cap gasket.
- Remove retaining ring (5) .
- Pull out strainer (6) .
- Wash the strainer in clean nonflammable solvent. Inspect the strainer for damage. If necessary, replace the strainer.
- Reinstall the strainer and associated components.
Oil Filter Elements
- Unscrew bolt (7) and remove the screen assembly.
Show/hide table
Illustration 3 | g00604821 |
- Remove cotter pin and washer (8) from bolt (7). Withdraw screen (9) and hydraulic filter elements (10). Discard both filter elements.
- Wash the screen in clean nonflammable solvent. Inspect the screen for damage. If necessary, replace the screen.
- Install two new hydraulic filter elements (10) into screen (9) .
- Assemble and reinstall the screen assembly as a unit. If necessary, use a new O-ring seal (11) .
Breather
- Unscrew breather (12) .
Show/hide table
Illustration 4 | g00604674 |
- Examine the breather and the breather seal for damage.
- Reinstall the breather. If necessary, install a new breather.
- Clean up any spilled oil.
- Install the hydraulic tank cover (1) .
- Install filler cap (3) and padlock (2) .
Caterpillar Information System:
3306C Engines for Caterpillar Built Machines Fuel Transfer Pump
769D Off-Highway Truck and 771D Quarry Truck Engine Start Switch
69D and 769D Off-Highway Truck and 771D Quarry Truck Power Train Speed Sensor (Transmission) - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
769D Off-Highway Truck/Tractor and 771D Quarry Truck Plate Locations and Film Locations
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Troubleshooting Diagnostic Codes
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Water Pump - Install
988G Wheel Loader Machine Systems Parking Brake - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Service Tools
69D and 769D Off-Highway Truck and 771D Quarry Truck Power Train Speed Sensor (Transmission) - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) General Information
D250E Series II and D300E Series II Articulated Trucks Hydraulic System Oil Level - Check
D250E Series II and D300E Series II Articulated Trucks Hydraulic Tank Screen - Clean
D250E Series II and D300E Series II Articulated Trucks In-Line Refrigerant Dryer - Check and Replace
69D and 769D Off-Highway Truck and 771D Quarry Truck Power Train Speed Sensor (Transmission) - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Troubleshooting Electrical System Using Abbreviated Procedures
3306C Engines for Caterpillar Built Machines Fuel Ratio Control
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Air Conditioner Belt - Inspect/Adjust/Replace
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Air Conditioner Condenser - Clean
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Troubleshooting Diagnostic Codes Using Abbreviated Procedure
769D Off-Highway Truck and 771D Quarry Truck Monitoring System
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Troubleshooting Service Codes
65E, 75E, 85E and 95E Agricultural Tractors Characteristics of Diesel Fuel