Dumping
- Position the machine straight ahead before dumping. Ensure that all the wheels are in contact with firm ground.
- Stop the machine with the service brake control. Move the parking and secondary brake control to the ENGAGED position.
- Move the transmission control to the N position.
- The machine must be stationary with the parking and secondary brake control in the ENGAGED position. The transmission control must be in the N position before the body is raised. Move the hoist control to the RAISE position and increase the engine speed.
- As the hoist cylinders approach full extension, reduce engine speed. Reduce hand pressure on the hoist control in order to slow the movement of the body. This could avoid damage to the hoist cylinders.
- Dump the load. Move the transmission control to the 1 position and move the parking and secondary brake control to the DISENGAGED position. Drive the machine slowly forward until the machine is clear of the load.
- Stop the machine with the service brake control. Move the parking and secondary brake control to the ENGAGED position.
- Move the transmission control to the N position.
- Move the hoist control to the LOWER position and increase the engine speed.
- Hold the hoist control until the body is about 600 mm (24 inch) from the frame. Release the hoist control and reduce the engine speed. The hoist control will move to the FLOAT position. The body will continue to lower under the effect of gravity until the body rests on the rear frame.
- Move the transmission control to the D position. Move the parking and secondary brake control to the DISENGAGED position and drive the machine to the new location. The transmission will remain in first gear until the hoist control is in the FLOAT position.
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Hauling
D350E Series II and D400E Series II Articulated Trucks Loading
3176C and 3196 Engines for Caterpillar Built Machines Cylinder Block
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Muffler - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Operating Technique Information
725C2 Articulated Truck Oscillating Hitch
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Electrical Components And Connector Locations
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) TPS Component Function
3406C Engines for Caterpillar Built Machines Exhaust Manifold
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) TPS On-Board Features
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) TPS Off-Board Features
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Truck Payload System (TPS) General Information
D250E Series II and D300E Series II Articulated Trucks Stopping the Machine
D250E Series II and D300E Series II Articulated Trucks Stopping the Engine
69D and 769D Off-Highway Truck and 771D Quarry Truck Power Train Rear Axle Housing and Differential - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Refill Capacities
D250E Series II and D300E Series II Articulated Trucks Stopping the Engine if an Electrical Malfunction Occurs
D250E Series II and D300E Series II Articulated Trucks Lowering the Body with Engine Stopped
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Limited Slip Differential - Disassemble
725C2 Articulated Truck Leaving the Machine
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Main Control Valve (Lift and Auxiliary)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) TPS Service Operation
IT28G Integrated Toolcarrier Caterpillar Approved Attachments
789C Off-Highway Truck Steering System Solenoid and Relief Valve (Steering)