Bogie Drive Chain Tension - Check/Adjust
Show/hide table
Illustration 1 | g00868493 |
- Start the engine. Raise one pendulum arm off the ground by approximately 305 mm (12 inch). Properly support the raised pendulum arm with wood blocks.
- Rotate boom (1) toward the opposite direction of raised pendulum arm (2) .
Show/hide table
Illustration 2 | g00482581 |
- Rotate the front wheel clockwise. When the wheel stops rotating, hold the wheel in this position until the check is complete. This removes the slack in the bogie drive chain.
Show/hide table
Illustration 3 | g00580965 |
- Mark a spot on the rear wheel. Rotate the rear wheel clockwise until the wheel stops rotating. Then, rotate the wheel counterclockwise until the wheel stops rotating.
- Note the distance of the rotation. The rear wheel should have rotated by 10 to 13 mm (0.38 to 0.50 inch).
If the bogie drive chain moved farther, an adjustment is required. Proceed with the following adjustment procedure.
Adjustment Procedure
Show/hide table
Illustration 4 | g00581007 |
Bogie drive chain (4) is driven by sprocket (3) that is connected to the front travel motor. The bogie drive chain is routed under two idler gears (5) that provide tension on the bogie drive chain. Bogie drive chain (4) should not be in contact with the bottom of bogie housing (7) .
Perform the following adjustment procedures if the tension of the bogie drive chain is incorrect.
- Loosen locknut (9) .
Show/hide table
Illustration 5 | g00581006 |
- Turn bolt (8) clockwise in order to increase the tension of the bogie drive chain. Turn bolt (8) counterclockwise in order to decrease the tension of the bogie drive chain.
Note: Do not overtighten the bogie drive chain. Overtightening the bogie drive chain causes a loss of rimpull to the wheels.
- Check the tension of the bogie drive chain. If the correct tension has not been reached, repeat the adjustment procedure.
Caterpillar Information System:
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0168 FMI 01 Electrical System Voltage Below Normal Range - Test
69D and 769D Off-Highway Trucks and 771D Quarry Truck Unit Injector Hydraulic Pump Drive - Install
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0144 FMI 06 Relay (Backup Alarm) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Main Module
784C and 785C Off-Highway Truck/Tractors Safety Messages
561M Pipelayer Power Train Hydraulic System
980G Wheel Loader Braking System Parking Brake System Pressure - Test
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Main Control Valve (Tilt and Auxiliary) - Install
793C Off-Highway Truck Machine Systems Truck Body and Canopy - Remove
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Main Control Valve (Tilt and Auxiliary) - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Slack Adjuster (Rear) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Electric Drive Pump (Secondary Steering) - Remove
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0248 FMI 09 CAT Data Link Abnormal Update - Test
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Aftercooler - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Air Cleaner - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Electrical Connector - Inspect
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0269 FMI 00 Sensor Power Supply Above Normal Range - Test
793C Off-Highway Truck Machine Systems Truck Body and Canopy - Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Refrigerant Condenser and Fuel Cooler - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Air Inlet Heater - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Alternator - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Drive Shaft - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Electric Starting Motor - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Engine - Install