Slack Adjuster (Rear) - Assemble
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 5P-3540 | 锁紧螺母扳手 | 1 |
| B | 1P-1861 | 挡圈钳 | 1 |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要，请更换部件。
- 利用所密封的润滑剂轻轻润滑所有 O 形密封圈。
Show/hide table
图 1 g00602675 - 将两个 O 形密封圈 ( 14) 和 (13) 安装到活塞 ( 12) 上。 将两个弹簧 ( 16)和 (15) 安装在活塞壳体 ( 9) 中。 将活塞 (12) 安装到活塞壳体 ( 9) 中。 将 O 形密封圈 ( 11) 置于活塞 (12) 的顶面上。
Show/hide table
图 2 g00602671 - 将 O 形密封圈 (10) 安装在活塞组件 ( 7) 上。
- 将活塞壳体 (9) 安装在活塞组件 ( 7) 中。
Show/hide table
图 3 g00602551 Show/hide table
弹簧压缩零件如果安装不当，会伤害人体。
为避免伤害，遵照出版的装配程序，并穿上保护装备。
- 用手向下推活塞壳体 ( 9)。 使用工具 (B) 将挡圈 ( 8) 安装在活塞组件 ( 7) 中。
Show/hide table
图 4 g00602520 - 将活塞组件 (7) 安装在壳体 ( 3) 中。
Show/hide table
图 5 g00481647 - 将 O 形密封圈 (6) 安装到盖 ( 4) 中。 将弹簧 (5) 安装到壳体 ( 3) 中。
Show/hide table
图 6 g00481646 Show/hide table弹簧压缩零件如果安装不当，会伤害人体。
为避免伤害，遵照出版的装配程序，并穿上保护装备。
注: 在弹簧力的作用下，壳体 ( 3) 固定于底座 (4) 上。 将壳体安装至底座 ( 4) 时，用手固定壳体 ( 3)。
- 将松紧调整器置于软面台钳中。 使用工具 (A) 将壳体 ( 3) 安装在底座 (4) 上。
- 对松紧调整器的另一侧重复步骤 3 至步骤 9。
Show/hide table
图 7 g01315988 - 将接头 (2) 安装在松紧调整器 ( 1) 中。
结束:
- 安装松紧调整器。 请参阅拆解和组装 , "松紧调整器（后）- 安装"。
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For MUI Engines Zero Display of Voltage or Current - Troubleshoot
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0144 FMI 03 Relay (Backup Alarm) Voltage Above Normal - Test
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Pilot Valve
Installation of 164-4636 Coolant Recovery Tank {1354} Installation of 164-4636 Coolant Recovery Tank {1354}
D250E Series II and D300E Series II Articulated Trucks Machine Systems Pressure Reducing Valve - Remove and Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Gear Pump (Implement, Steering and Brakes) - Remove
Repairing the Nonmetallic Fenders, Machine Hoods, and Tank Covers {1273, 7251, 7252} Repairing the Nonmetallic Fenders, Machine Hoods, and Tank Covers {1273, 7251, 7252}
24H Motor Grader Power Train Hydraulic Filter (Differential)
980G Wheel Loader Braking System Parking Brake Control Cable - Adjust
D250E Series II and D300E Series II Articulated Trucks Machine Systems Hoist Control Valve - Assemble
980G Wheel Loader Braking System Parking Brake - Manual Release
69D and 769D Off-Highway Trucks and 771D Quarry Truck Unit Injector Hydraulic Pump Drive - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Slack Adjuster (Rear) - Disassemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Gear Pump (Implement, Steering and Brakes) - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Slack Adjuster (Rear) - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Hydraulic Caliper Service Brake - Assemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Electric Drive Pump (Secondary Steering) - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Slack Adjuster (Rear) - Remove
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Main Control Valve (Tilt and Auxiliary) - Remove
793C Off-Highway Truck Machine Systems Truck Body and Canopy - Remove
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Main Control Valve (Tilt and Auxiliary) - Install
980G Wheel Loader Braking System Parking Brake System Pressure - Test
561M Pipelayer Power Train Hydraulic System
784C and 785C Off-Highway Truck/Tractors Safety Messages