Tattletale Mode
Show/hide table
图 1 | g00301362 |
显示区 |
Show/hide table
图 2 | g00559808 |
Caterpillar 监控系统 显示部件 (1) 四表组模块。 (2) 速度表/转速表组件。 (3) 主显示模块。 (4) 警告指示器。 (5) 仪表。 (6) 转速表。 (7) 速度读数区。 (8) 变速箱档位读数区。 (9) 显示区。 |
信息指示模式是一种管理和保养方式。 机器历史可在这种模式下被记录。 主显示模块记录被监测的机器在各种情况下的极值。 这些数值来自传感器输入、开关输入和 Cat 数据链路。 只要比先前值更重要的值出现,信息指示模式下的值都会被更新。 在每台发动机起动后一个短时间内这些数值会被忽略。 这使得机器系统在记录信息前稳定下来。
仪表 (5) 显示相应机器系统所达到的最高和最低读数。 仪表显示异常升高值的最高读数。 仪表也显示异常下降值的系统的最低读数。 仪表在最高和最低读数之间更换。 在双头仪表上会出现这种情况。
转速表 (6) 和速度读数区 (7) 显示所得到的最高读数。
当存在异常状况时,报警指示灯 (4) 点亮。
信息指示模式中的信息将被保留直至信息清除。 将清除输入接地会删除信息。 清除后,所有信息回到正常数值,并开始记录新的极值。
注: 所发生极值的日期、时间和持续时间未被记录。
范例
这个示例说明了信息指示模式图示中提供的信息。
- 发动机冷却液温度表 (5) 指针指示的数值高于正常温度范围。 因此,本系统中存在高异常值。
- 进气压力表 (5) 指针指示的数值低于正常压力范围。 因此,本系统中存在低异常值。
- 变矩器油温表 (5) 指针指示的数值处于正常范围。 因此,系统中不存在异常值。
- 燃油油位仪表 (5) 指针指示 50% 油位。 因此,已存在的最高燃油量为 50%。
- 转速表 (6) 指针指示最大值(2100 RPM)。 因此,存在发动机转速 2100 RPM。
- 速度读数区 (7) 显示 "13 MPH"。 因此,13 MPH 是所获得的最高行驶速度。
- 报警指示灯 (4) 点亮(ON)。 因此,本系统中存在异常情况。
- 所有其他报警指示灯 (4) 被关闭(OFF)。 因此,系统中不存在异常值。
注: 对选择的最高档或最低档未存储来自信息指示模式的相关信息。
Caterpillar Information System:
572R Pipelayer Tracks
784C and 785C Off-Highway Truck/Tractors Steering System Front Wheel Bearing - Adjust
VFS50 and VFS70 Versatile Flotation System Belts - Inspect/Adjust/Replace
VFS50 and VFS70 Versatile Flotation System Special Torques
IT14G Integrated Toolcarrier Starting Above 0°C (32°F)
IT14G Integrated Toolcarrier Walk-Around Inspection
VFS50 and VFS70 Versatile Flotation System Installation of Scale Group
572R Pipelayer Power Train Oil Cooler
IT14G Integrated Toolcarrier Bucket Kickout and Positioner Control
583R Pipelayer Power Train Track Roller
3406E and 3456 Engines for Caterpillar Built Machines Compression Brake
IT14G Integrated Toolcarrier Hydraulic Lockout Control
784B and 785B Off-Highway Truck/Tractors Steering System Front Wheel - Align
784C and 785C Off-Highway Truck/Tractors Steering System Relief Valve (Cylinder Crossover) - Test and Adjust
3054 Engine Rocker Shaft
VFS50 and VFS70 Versatile Flotation System Idler Bearings - Lubricate - Earlier Trailers
Caterpillar Monitoring System Units Mode
416C, 426C, 428C, 436C and 438C Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Rear)
572R Pipelayer Transmission Oil Filter
VFS50 and VFS70 Versatile Flotation System Walk-Around Inspection
Caterpillar Monitoring System Setup Mode
583R Pipelayer Power Train Pivot Shaft
IT14G Integrated Toolcarrier Machine Operation Information
IT14G Integrated Toolcarrier Changing Speed and Direction