Front Wheel Bearing - Adjust
Show/hide table
Illustration 1 | g00288128 |
(1) Axle (2) Wheel (3) Nut (4) Nut (5) Bolt (6) Retainer (7) Bolt (8) Shim (9) Seals (10) Bearing (11) Bearing |
Wheel Bearing Adjustment
Note: Before you proceed, tap the thread holes by hand or use a wire brush on the thread holes to remove the thread lock compound.
- Install wheel (2) and bearing assemblies (10) and (11) onto axle (1) .
- Without using shims (8) , use four bolts (7) to assemble retainer (6) to axle (1) . Be sure that bolts (7) are equally spaced.
- Torque four bolts (7) to 80 N·m (59 lb ft).
- Rotate the wheel for two revolutions in order to seat the bearings.
- Torque four bolts (7) to 80 N·m (59lb ft).
- Rotate the wheel for two revolutions.
- Torque four bolts (7) to 80 N·m (59 lb ft).
- Rotate the wheel for two revolutions in order to seat the bearings.
- Use a depth micrometer at the two threaded holes in retainer (6) to measure the distance from the end of axle (1) to the outer face of retainer (6) . Record the average of the measurements.
- Remove retainer (6) . Measure the thickness of retainer (6) at the two threaded holes that were used to get the previous measurements. Record the average of the measurements.
- Use the average distance from the end of axle (1) to the outer face of retainer (6) . Subtract the average thickness of retainer (6) from this measurement. This measurement is the distance from the end of axle (1) to the inner face of retainer (6) .
- Install shim pack (8) . In order to determine the shim pack thickness, add 0.340 mm (0.0134 inch) to the distance that was found in the previous step.
Note: Before final assembly, apply Loctite 242 Blue Threadlocker to bolts (7) .
- Install 14 bolts (7) . Torque bolts (7) to 250 ± 14 N·m (184 ± 10 lb ft).
Caterpillar Information System:
VFS50 and VFS70 Versatile Flotation System Belts - Inspect/Adjust/Replace
VFS50 and VFS70 Versatile Flotation System Special Torques
IT14G Integrated Toolcarrier Starting Above 0°C (32°F)
IT14G Integrated Toolcarrier Walk-Around Inspection
VFS50 and VFS70 Versatile Flotation System Installation of Scale Group
572R Pipelayer Power Train Oil Cooler
IT14G Integrated Toolcarrier Bucket Kickout and Positioner Control
583R Pipelayer Power Train Track Roller
3406E and 3456 Engines for Caterpillar Built Machines Compression Brake
IT14G Integrated Toolcarrier Hydraulic Lockout Control
784B and 785B Off-Highway Truck/Tractors Steering System Steering Accumulator - Test and Charge
784C and 785C Off-Highway Truck/Tractors Steering System Relief Valve (Steering) - Test and Adjust
572R Pipelayer Tracks
Caterpillar Monitoring System Tattletale Mode
784B and 785B Off-Highway Truck/Tractors Steering System Front Wheel - Align
784C and 785C Off-Highway Truck/Tractors Steering System Relief Valve (Cylinder Crossover) - Test and Adjust
3054 Engine Rocker Shaft
VFS50 and VFS70 Versatile Flotation System Idler Bearings - Lubricate - Earlier Trailers
Caterpillar Monitoring System Units Mode
416C, 426C, 428C, 436C and 438C Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Rear)
572R Pipelayer Transmission Oil Filter
VFS50 and VFS70 Versatile Flotation System Walk-Around Inspection
Caterpillar Monitoring System Setup Mode
583R Pipelayer Power Train Pivot Shaft