1979/08/27 Caterpillar


6V190 Clamp Is Available For Use On Sleeve Metering Fuel Systems{0626,1250}

Usage:


All Sleeve Metering Fuel Systems

The 6V190 Clamp is now available for use on sleeve metering fuel systems. It is a direct replacement for the former 5P6562 Spring which is canceled. The new clamp holds the sleeve control shaft against the bearings to check or adjust the sleeve levers. The new clamp is held by a bolt to the cover of the fuel injection pump housing. It was possible for the former spring to become free.


The new 6V190 Clamp in use.

Caterpillar Information System:

1979/08/27 New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27 Steering System Improvements Prevent Possible Damage To Steering Cylinder Sockets{4303,4304,4305,4322}
1979/08/27 New Seal For Precombustion Chamber Has More Resistance To Heat And Steam{1106}
1979/08/27 Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/20 New Rear Cover And Gasket Used On Water Pump{1361,1350}
1979/08/20 Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20 Pump Failure Can Be Prevented{5070,5200}
1979/08/20 Flex Plate Kits Are Now Available For Vickers Vane-Type Hydraulic Pumps{5055}
1979/08/13 Sealant Now Used On Pipe Plugs At The Bottom Of The Oil Filter Base Assembly To Prevent Oil Leakage{1306}
1979/08/13 New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13 New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13 6V14 Hydraulic Cylinder Group Now Available{0621}
1979/08/27 Hardened Washers And Increased Torque Are Now Used On The Bolts Which Fasten The Circle Drive Group To The Circle Drawbar{5207,6153}
1979/08/27 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U. S. Factories{1318}
1979/08/27 New Rocker Arms And Rocker Arm Shaft Have Improved Lubrication{1102}
1979/08/27 New Design Thrust Plate Used In Crankshaft Group{1201,1202,1203}
1979/09/03 Use Caution To Prevent Damage To Plastic Check Valve In Hydraulic Oil Tank And Transmission Oil Tank Drain{5056,3177}
1979/09/03 Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/09/03 Follow Recommendations Given In Special Instructions For Modification Of Rollover Protective Structures (ROPS) At All Times{7323,7325}
1979/09/03 Important: Use Only 8N4029 Fan On 769C Trucks And 768C Tractors{1356}
1979/09/03 Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03 Improved Wire Assembly For Glow Plugs{1403}
1979/09/03 Improved Hardware Now Used To Fasten Front Suspension Cylinder To Frame{7201}
1979/09/10 Insulation Sleeve For 5P7360 Tach Generator Now Available {7462}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.