Do Not Use Room Temperature Vulcanizer Compounds Or Silicone Rubber Cements On O-Ring Seals In Engines; Do Not Use Too Much As Gasket Material {1000,7555}
Usage:
All Applications
Do not use RTV (room temperature vulcanizers) compounds or silicone rubber cements with O-rings to give a better seal in engines. The extra compound or cement can close oil and cooling passages, heat exchangers, piston cooling jets, etc. There have been reports of engine failures caused by these materials. If the seal is the right size and the groove is clean and not worn, these materials will not improve the sealed joint.
When you use RTV's or cements as a gasket cement, be sure to remove any extra material from the surfaces. Follow recommendations for use of these materials.
Caterpillar Information System:
1980/09/22 New Clamp Gives Protection To Tire Valve Assembly {4201,4202,4208}
1980/09/22 Install New Damper Assemblies During Assembly Of Radiator And Guard {1353,1381}
1980/09/22 Do Not Use Planet Gears Made From Forgings And Bar Stock Together In A Torque Divider Transmission {3110,3113,3114,3116,3118}
1980/09/22 6V3071 Seal Guide Keeps Seal In Position During Installation Of Transfer Pump {0620,1256}
1980/09/15 Use Only Caterpillar Water Separator Elements{1263}
1980/09/15 Reference List Of Pistons Used With The Different Types Of Connecting Rods{1214,1218}
1980/09/15 Use Only CC Or CD Oil In Final Drives{4070}
1980/09/15 Improvements To Final Drive Group{4091,4054,4059,4055}
1980/09/15 Special Cup Plugs For Use In Oversize (Larger Than Standard Size) Bores In Valve Rocker Arm Shafts{1102}
1980/09/15 Reverse Flow Check Valves And Check Valves With A Groove Can Not Be Used In Place Of Each Other{1251,1272,1254}
1980/09/15 6V2107 And 6V2110 Drive Adapter Assemblies Available To Connect Sleeve Metering Fuel Systems To Fuel Injection Test Bench{0652,1250}
1980/09/15 6V3025 Battery Cable Repair Kit Now Available{1402,1408,0611}
1980/09/22 Use Correct Procedures To Charge Suspension Cylinders With Oil {7201}
1980/09/22 Install A New Oil Filter Element, Clean The Oil Lines And The Remote Filter Base; Turn The Engine Until The Oil Gauge Shows Pressure Before Starting A Rebuilt Engine {1307,1318}
1980/09/29 FT1535 Idler Bearing Puller Available{0621,4167,4159}
1980/09/29 Woodward 2301 Speed Control (8N1731 Speed Control Group) Can Be Adapted For Use As Field Test Instrument{0651,1264,1265,1289}
1980/09/29 Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29 Use Starter To Turn Crankshaft For 30 Seconds Or Until Oil Pressure Gauge Shows Pressure, Before Engine Is Started{1300,1450}
1980/10/06 Fretting Material Must Be Removed Before Installation Of New Bearings{1202,1203,1218,1219,1201,1230}
1980/10/06 New Timing Advance Weight Used{1272,1288,1286,1264}
1980/10/13 6V3184 Brush Group Available To Clean Crankshaft Oil Passages{0622,1202}
1980/10/13 6V2156 And 6V2157 Link Brackets Now Available To Lift Heavy Loads{0644}
1980/10/13 New Tools Available For Installation Of Crankshaft Seals And Wear Sleeves{0622,1160,1161}
1980/10/13 6V3116 Adapter Group Is Available For Use On Fuel Injection Test Bench{0652,1251}