6V2156 And 6V2157 Link Brackets Now Available To Lift Heavy Loads{0644}
Usage:
The 6V2156 and 6V2157 Link Brackets are now available for general purpose use when it is necessary to lift heavy loads (Illustration). The new 6V2156 Link Bracket has a load capacity of 2,250 lbs. (1023 kg) and is attached to the load with a .375" (9.53 mm) bolt. The new 6V2157 Link Bracket has a load capacity of 9,000 lbs. (4091 kg) and is attached to the load with a .75" (19.05 mm) bolt.
In the past, standard eyebolts have been used to lift heavy loads. These eyebolts have a decreased ability to lift loads at an angle. The bracket links can lift loads at any angle and need less clearance than an eyebolt.
Caterpillar Information System:
1980/10/13 6V3184 Brush Group Available To Clean Crankshaft Oil Passages{0622,1202}
1980/10/06 New Timing Advance Weight Used{1272,1288,1286,1264}
1980/10/06 Fretting Material Must Be Removed Before Installation Of New Bearings{1202,1203,1218,1219,1201,1230}
1980/09/29 Use Starter To Turn Crankshaft For 30 Seconds Or Until Oil Pressure Gauge Shows Pressure, Before Engine Is Started{1300,1450}
1980/09/29 Some Test Procedures And Specifications Changed For 9L6884 Fuel Injection Nozzle Assemblies{1254,0651}
1980/09/29 Woodward 2301 Speed Control (8N1731 Speed Control Group) Can Be Adapted For Use As Field Test Instrument{0651,1264,1265,1289}
1980/09/29 FT1535 Idler Bearing Puller Available{0621,4167,4159}
1980/09/22 Install A New Oil Filter Element, Clean The Oil Lines And The Remote Filter Base; Turn The Engine Until The Oil Gauge Shows Pressure Before Starting A Rebuilt Engine {1307,1318}
1980/09/22 Use Correct Procedures To Charge Suspension Cylinders With Oil {7201}
1980/09/22 Do Not Use Room Temperature Vulcanizer Compounds Or Silicone Rubber Cements On O-Ring Seals In Engines; Do Not Use Too Much As Gasket Material {1000,7555}
1980/09/22 New Clamp Gives Protection To Tire Valve Assembly {4201,4202,4208}
1980/09/22 Install New Damper Assemblies During Assembly Of Radiator And Guard {1353,1381}
1980/10/13 New Tools Available For Installation Of Crankshaft Seals And Wear Sleeves{0622,1160,1161}
1980/10/13 6V3116 Adapter Group Is Available For Use On Fuel Injection Test Bench{0652,1251}
1980/10/13 Improved Temperature Control Switch Used On Machines Equipped With Air Conditioner Units{7320}
1980/10/13 Correct Assembly Of Shuttle Valve In Pump Control Head Group Is Important{5079,5070}
1980/10/13 Understand The Effects Of Extended Oil And Filter Change Intervals{0375}
1980/10/20 Instructions For Modification Of The 5P8630 Driver Head Which Is Part Of The 6V82 Final Drive Bearing Adjustment Tool Arrangement{0654,4050}
1980/10/20 Valve Assembly Used In Centershift Lock Control Group To Prevent Accidental Rotation And Lowering Of Blade{5220,5221,5223,6151}
1980/10/20 Larger Diameter Retainer Ring Used To Hold Rear Bearing In Transmission{3176,3150}
1980/10/20 New Fan Motor Used In Basic Heater Groups{7304}
1980/10/20 Before You Use Any Service Publication, Make Sure It's Current{0374}
1980/10/27 Gauge Group Improvements; Recommendation To Change Machines Equipped With Modular Cabs{7455,7456}
1980/10/27 New Repair Kit Available For Vent Assemblies Used In Fast Fill Fuel Adapter Groups{1273}