Air Compressor Drive Gear - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 132-5451 | Holding Fixture | 1 |
Start By:
- Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Show/hide table
Illustration 1 | g01148907 |
- Install Tooling (A) on air compressor drive gear (1).
- Remove nut (2).
- Remove air compressor drive gear (1).
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 132-5451 | Holding Fixture | 1 |
Note: Caterpillar may use air compressors that have a tapered shaft or a straight shaft. The torque for the nut on the air compressor crankshaft is different for each type of crankshaft.
Note: Identify the manufacturer of the air compressor for your particular application.
- Install air compressor drive gear (1) on the air compressor.
- Install Tooling (A) on air compressor drive gear (1).
- Install nut (2).
Show/hide table
Illustration 2 | g01148907 |
Tapered Shaft on Bendix Air Compressor
- Tighten nut (2) to a torque of
160 ± 15 N·m (118 ± 11 lb ft) . - Tap the gear axially with a soft faced hammer to seat the gear onto the tapered crankshaft.
- Tighten the nut again to a torque of
160 ± 15 N·m (118 ± 11 lb ft) .
Straight Shaft on Bendix Air Compressor
- Tighten nut (2) to a torque of
460 ± 60 N·m (340 ± 44 lb ft) .
- Tighten nut (2) to a torque of
150 ± 5 N·m (111 ± 4 lb ft) . - Place an index mark on the nut and rotate nut (2) an additional 60 ± 5 degrees.
End By:
- Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Air Compressor - Remove and Install - If Equipped
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems Hydraulic Lockout Control - Remove and Install
140 Motor Graders Tandem and Cover
320, 323 Excavator Engine Supplement Fuel Filter and Base - Remove and Install
140 Motor Grader Engine Supplement Vibration Damper and Pulley - Remove and Install
797F Tier 4 Off-Highway Truck Engine Supplement Guard (Engine Oil Pan) - Remove and Install
323 Excavator Engine Supplement Fuel Filter and Base - Remove and Install
140 Motor Grader Machine Systems Hydraulic Tank and Filter - Remove and Install
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Track Adjustment - Adjust
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Electronic Control (Travel System)
140 Motor Grader Engine Supplement Catalyst (SCR) - Remove and Install
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Electronic Control (Swing System)
140 Motor Graders Transmission Filter and Mounting
140 Motor Grader Engine Supplement Engine Support (Front) - Remove and Install
320 GC, 320 and 323 Excavator Machine Systems Specifications Front Lines
Alternator Troubleshooting On Certain 3024C, C1.7, C2.2, C4.4, and C7.1 Engines {1405} Alternator Troubleshooting On Certain 3024C, C1.7, C2.2, C4.4, and C7.1 Engines {1405}
320 GC, 320 and 323 Excavator Machine Systems Specifications Boom Lines
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems Undercarriage Cylinder (Adjustable Gauge) - Disassemble
140 Motor Grader Engine Supplement Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
301.5,301.6,301.7,301.8,302 Mini Hydraulic Excavator Machine Systems Undercarriage Cylinder (Adjustable Gauge) - Assemble
140 Motor Grader Engine Supplement Pressure Sensor (ARD Combustion Air) - Remove and Install
140 Motor Grader Engine Supplement Nozzle Heater Harness - Remove and Install
120 Motor Graders Wheel Lean Cylinder and Mounting
320 GC, 320 and 323 Excavator Machine Systems Specifications Boom Lines