Swing Gear and Bearing
Show/hide table
| |
| Illustration 1 | g02961976 |
|
Top view | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| - | - | - | Position "S" that is on inner race (3) relative to the carbody assembly (1) and bearing stopper (2). Refer to Illustration 1. |
Show/hide table
| |
| Illustration 2 | g02961857 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 4 | 2 | 8T-4137 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
| 5 | 1 | 7Y-1650 Hose Clamp | Torque to |
| 6 | 8 | 8T-4136 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
| 7 | 1 | 7Y-1095 Dowel | Before assembly, apply Loctite C5A Copper Anti-Seize Compound to the dowel holes. |
| 8 | - | - | Before assembly, apply 8C-8422 Sealant between the mating surfaces of the gear group and upper frame assembly. and between the gear group and carbody assembly. |
| 9 | 4 | 8T-4136 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
| 10 | 42 | 461-3888 Bolt | Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper Anti-Seize Compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 65 ± 5 degrees. |
| 11 | 46 | 461-3885 Bolt | Before assembly, remove compound, oil and dust from female threads, then apply Loctite C5A Copper Anti-Seize Compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 55 ± 5 degrees. |
Caterpillar Information System:
336 and 336 GC Excavator Fuel Tank Water and Sediment - Drain
336 and 336 GC Excavator Engine Air Filter Primary and/or Secondary Element - Replace
Regulatory Compliance Information Radio Detection and Ranging (Radar) - C5 Radar - If Equipped
336 and 336 GC Excavator Parking
797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160} 797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Control Valve (Boom Lowering)
Thermocouples May Fail on Certain G3500 Engines {7498} Thermocouples May Fail on Certain G3500 Engines {7498}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Boom System)
Rework Procedure for Muffler/Silencers on Certain G3516 Power Modules {1062} Rework Procedure for Muffler/Silencers on Certain G3516 Power Modules {1062}
336, 336 GC and 340 Excavator Systems Swing Motor
C175-16 and C175-20 Engines for Caterpillar Built Machines Centrifugal Oil Filter - Assemble
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Temperature Sensor (DPF) - Remove and Install
336, 336 GC and 340 Excavator Systems Manifold and Reducing Valve (Pilot Oil)
301.5, 301.6, 301.7CR, 301.8, 302CR Mini Hydraulic Excavators Machine System Stick
336, 336 GC and 340 Excavator Systems Position Sensor and Mounting
336, 336 GC and 340 Excavator Systems Suction Fan
336, 336 GC and 340 Excavator Systems Front Lines
336, 336 GC and 340 Excavator Systems Fuel Tank and Mounting
336, 336 GC and 340 Excavator Systems Fuel Tank
336, 336 GC and 340 Excavator Systems Track Adjuster and Recoil
336, 336 GC and 340 Excavator Systems Pump Lines
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553} Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
336 and 336 GC Excavator Swing Drive Oil - Change
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Boom Cylinder