Centrifugal Oil Filter - Assemble
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 502-1421 | Oil Filter Tool | 1 |
Note: A CWS login is required to access Caterpillar Channel 1.
Reference: For additional information, view "C175 Centrifugal Oil Filter Clean for 797 Off-Highway Trucks" on Caterpillar Channel 1.
English
https://channel1.mediaspace.kaltura.com/media/C175+Centrifugal+Oil+Filter+Clean+for+797+Off-Highway+Trucks/1_j1rgf35vSpanish
https://channel1.mediaspace.kaltura.com/media/Filtro+de+aceite+centr%C3%ADfugo+C175+limpio+para+797+camiones+fuera+de+carretera+%28Spanish%29/1_4sz0t21iPortuguese
https://channel1.mediaspace.kaltura.com/media/Filtro+de+%C3%B3leo+centr%C3%ADfugo+C175+limpo+para+797+caminh%C3%B5es+fora+de+estrada++%28Portuguese%29/1_o0si7vobShow/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Ensure that all of the rotor components are thoroughly clean before assembling the rotor. Failure to do so can cause an out of balance condition that can cause rapid wear to the bearings and the spindle. |
- Install O-ring (22) on retainer (20).
Show/hide table
Illustration 2 g06317336 - Install retainer (20) into the cover assembly.
- Install tube (21) and install pin (19).
Show/hide table
Illustration 3 g06317358 - Install clip (14) and O-ring (16) onto spindle (15).
Show/hide table
Illustration 4 g06318019 Show/hide table
Illustration 5 g06318027 - Secure Tooling (A) in a bench vise. Place a socket on Tooling (A) to hold the rotor assembly.
- Place spindle (15) and rotor base on Tooling (A).
- Install plate (13), O-ring (12), and rotor tube (11).
Show/hide table
Illustration 6 g06317287 - Install the paper liner (10) from rotor tube (11).
Show/hide table
Illustration 7 g06317282 - Install O-ring (9) and clip (8).
- Install cover (7) and tighten nut (6) to a torque of
40 ± 6 N·m (29.5 ± 4.5 lb ft) .Show/hide table
Illustration 8 g06289059 - Install rotor assembly (5) onto the filter base.
Show/hide table
Illustration 9 g06289052 - Install O-ring seal (4) onto the filter base.
Show/hide table
Illustration 10 g06289047 - Loosen clamp (3) and nut (1). Remove cover (2) from the filter base.
- Install cover assembly (2) and hand tighten nut (1).
- Install clamp (3). Tighten clamp (3) to a torque of
20 ± 2 N·m (177 ± 18 lb in) - Tighten nut (1) to a torque of
15 ± 2 N·m (133 ± 18 lb in)
Show/hide table
| |
| Illustration 1 | g06317347 |
End By:
- Install the centrifugal oil filter. Refer to Disassembly and Assembly, "Centrifugal Oil Filter - Remove and Install".
Caterpillar Information System:
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Temperature Sensor (DPF) - Remove and Install
336, 336 GC and 340 Excavator Systems Engine Mounting
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Main Control Valve)
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Main Pump System)
336, 336 GC and 340 Excavator Systems Drift Reduction Valve
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Water Temperature Regulator - Remove and Install
336, 336 GC and 340 Excavator Systems Stick Cylinder
301.5, 301.6, 301.7CR, 301.8, 302CR Mini Hydraulic Excavators Machine System Return Lines
301.5, 301.6, 301.7CR, 301.8, 302CR Mini Hydraulic Excavators Machine System Pump Lines
301.5, 301.6, 301.7CR, 301.8, 302CR Mini Hydraulic Excavators Machine System Pilot Lines
336, 336 GC and 340 Excavator Systems Stick
301.5, 301.6, 301.7CR, 301.8, 302CR Mini Hydraulic Excavators Machine System Joystick Control
336, 336 GC and 340 Excavator Systems Swing Motor
Rework Procedure for Muffler/Silencers on Certain G3516 Power Modules {1062} Rework Procedure for Muffler/Silencers on Certain G3516 Power Modules {1062}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Boom System)
Thermocouples May Fail on Certain G3500 Engines {7498} Thermocouples May Fail on Certain G3500 Engines {7498}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Control Valve (Boom Lowering)
797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160} 797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160}
336 and 336 GC Excavator Parking
Regulatory Compliance Information Radio Detection and Ranging (Radar) - C5 Radar - If Equipped
336 and 336 GC Excavator Engine Air Filter Primary and/or Secondary Element - Replace
336 and 336 GC Excavator Fuel Tank Water and Sediment - Drain
336, 336 GC and 340 Excavator Systems Swing Gear and Bearing
336, 336 GC and 340 Excavator Systems Manifold and Reducing Valve (Pilot Oil)