Stick
Show/hide table
Illustration 1 | g06289738 |
Typical example |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
- | All bores must be free of paint. Use the 5P-0960 Grease Cartridge in order to coat all bores and sealing lips with lubricant before assembly, and lubricate all joints from fitting after assembly. | ||
1 | 1 | 521-4176 Pin As | Diameter is |
2 | 2 | 521-4193 Bushing | Before assembly, inside diameter is Installation depth is |
3 | 4 | 8T-4191 Bolt | Torque to |
4 | As required, use the following shims to adjust the maximum lateral clearance to |
||
1 | 139-4268 Shim | Thickness is |
|
1 | 304-8218 Shim | Thickness is |
|
5 | 4 | 270-6549 Bushing | Before assembly, inside diameter is Installation depth is |
6 | As required, use the following shims to adjust the maximum lateral clearance to |
||
1 | 139-4268 Shim | Thickness is |
|
1 | 304-8218 Shim | Thickness is |
|
7 | 1 | 540-1967 Pin As | Diameter is |
8 | 1 | 521-4177 Pin As | Diameter is |
9 | As required, use the following shims to adjust the maximum lateral clearance to |
||
1 | 139-6384 Shim | Thickness is |
|
1 | 139-6383 Shim | Thickness is |
Caterpillar Information System:
336, 336 GC and 340 Excavator Systems Manifold and Reducing Valve (Pilot Oil)
336, 336 GC and 340 Excavator Systems Swing Gear and Bearing
336 and 336 GC Excavator Fuel Tank Water and Sediment - Drain
336 and 336 GC Excavator Engine Air Filter Primary and/or Secondary Element - Replace
Regulatory Compliance Information Radio Detection and Ranging (Radar) - C5 Radar - If Equipped
336 and 336 GC Excavator Parking
797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160} 797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Control Valve (Boom Lowering)
Thermocouples May Fail on Certain G3500 Engines {7498} Thermocouples May Fail on Certain G3500 Engines {7498}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Boom System)
Rework Procedure for Muffler/Silencers on Certain G3516 Power Modules {1062} Rework Procedure for Muffler/Silencers on Certain G3516 Power Modules {1062}
336, 336 GC and 340 Excavator Systems Swing Motor
336, 336 GC and 340 Excavator Systems Position Sensor and Mounting
336, 336 GC and 340 Excavator Systems Suction Fan
336, 336 GC and 340 Excavator Systems Front Lines
336, 336 GC and 340 Excavator Systems Fuel Tank and Mounting
336, 336 GC and 340 Excavator Systems Fuel Tank
336, 336 GC and 340 Excavator Systems Track Adjuster and Recoil
336, 336 GC and 340 Excavator Systems Pump Lines
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553} Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
336 and 336 GC Excavator Swing Drive Oil - Change
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Boom Cylinder
336 and 336 GC Excavator Swing Drive Oil Level - Check
336, 336 GC and 340 Excavator Systems Hydraulic Oil Cooler Lines Group