Safety
Show/hide table
进行电路相关工作很危险,使工作人员面临触电的危险。 为了确保安全操作,工作人员必须经过培训,掌握正确的操作步骤。 触电可能造成严重的人身伤害甚至死亡。 |
光伏模块可以单独产生高达 90V 和 2A 的电压。 当与其他模块连接且阳光直射时,模块可以产生高达 900V 和 25A 的电压。 单个模块可以在白天的几个小时和低光照水平的时段内产生致命的电击危险。 随着模块串联和/或并联连接在一起,危险性增加。
请阅读以下说明,以避免由于接地故障或相关电气危害引起的火灾和/或伤害:
- 负载时请勿拔下光伏模块连接。
- 白天期间请勿断开模块接头,除非出现以下情况之一:
- 该模块处于开路状态。
- 串联和并联的所有模块都覆盖着不透明材料,如篷布或毛毯。
- 立即修理或更换损坏的导线。
- 无资质的人员要远离所有阵列导线。
- 不要通过将光照集中在模块上来尝试增加输出功率。
- 任何情况下都不要让光伏阵列系统电压超过 1500 VDC。
- 立即更换损坏的模块。
- 立即修理所有接地故障。
- 当模块或导线潮湿时,不要在模块或系统上工作。
注: 如果反向电流大于光伏模块的额定值,反向电流过载将会导致模块故障,包括模块毁坏。
极端和连续的反向电流过载情况将导致火灾或造成触电危险。 使用以下信息来帮助避免反向电流过载:
- 通过在同一个电源电路内安装相同数量的模块串组,来保持并联串组的电压相等。 在并联串组中安装电压不平衡的模块可能会导致电压不平衡。
- 遵守本文所述的所有规程并修理接地故障。
- 在非互连模块或系统上工作时,请戴好护目镜和防切割手套。
- 在互连模块或系统部件上工作时,请戴好适当电气额定值的个人防护设备(PPE)。
注: 为避免火灾风险,只能连接额定值相近的模块。 连接 PVT110 模块和与同一互连串组中的其他 PVT110 模块。 同样,仅将 PVT115 4V3 模块与同一串联线路内的其他 PVT115 4V3 模块相连,将 PVT117 4V3 模块与同一串联线路内的其他 PVT117 4V3 模块相连。
Caterpillar Information System:
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087} Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087} Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Machine Drift on a Slope - Check
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Travel on Level Ground - Test - Optional Test
C18 Generator Sets Generator Lead Connections
PM820, PM822, and PM825 Cold Planer Machine Systems Rotor Drive Planetary - Remove and Install
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Module - Clean
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Travel on Level Ground - Test
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Mirror
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Engine Performance - Test - Engine Speed
C18 Generator Sets Single Unit Operation
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Main Hydraulic Pump Air - Purge
The Connecting Rod Bolt Has a New Look for All 3600, C280, and G3600 Engines {1218} The Connecting Rod Bolt Has a New Look for All 3600, C280, and G3600 Engines {1218}
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Inverter - Clean
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Swing Speed and Overswing on Level Ground - Check
New Software Is Now Used on 3500E Marine Engines {1920, 7620} New Software Is Now Used on 3500E Marine Engines {1920, 7620}
336, 336 GC and 340 Excavator Systems System Schematic
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Swing Speed and Swing Drift on a Slope - Check
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Cylinder Drift - Check
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Window (Front)
A New Alternator Bracket Is Now Used on Certain 374F and 390F Excavator Engines {1405} A New Alternator Bracket Is Now Used on Certain 374F and 390F Excavator Engines {1405}
C9.3B Engines Cylinder Block Cover Group
C7.1 Marine Propulsion Engine Piston Cooling Jets - Remove and Install
336 and 336 GC Excavator Camera