Swing Speed and Overswing on Level Ground - Check
Show/hide table
"在平地上的回转速度和摆动过量 - 检查" | |
---|---|
项目 | 技术规格 |
回转过量(1) mm(in) | |
向右回转 | |
向左回转 | |
水平地面上的回转加速(2) (秒) | |
向右回转 | 2.5 或以下 |
向左回转 | |
回转速度(三圈)(3) (秒) | |
向右回转 | 16.5 - 19.5 或更少 |
向左回转 |
Show/hide table
(1) | 负载铲斗 |
(2) | 90 度回转的技术规格 |
(3) | 在机器旋转一整圈后开始测量 |
测量机器的回转速度和回转过量可以确定是否需要检查回转马达。
注: 发动机转速和 / 或测试期间所用的机器配置可能对测试结果产生影响。 有关此项测试所用的发动机转速,请参阅测试和调整, "发动机性能 - 测试(发动机转速)"。 有关此项测试所用的机器配置,请参阅测试和调整, "操作检查"。
注: 执行操作检查之前,必须根据卸压阀压力技术规范设定卸压阀压力。 请参阅测试和调整, "技术规范"。
Show/hide table
所需工具 | |
---|---|
说明 | 数量 |
卷尺 | 1 |
秒表 | 1 |
Show/hide table
图 1 | g06278110 |
- 将机器停放在水平地面上。 参考图 1。
- 完全回缩斗杆油缸,然后完全伸出铲斗油缸。
- 停止发动机。
Show/hide table
图 2 g06194809 (A) 上部机架
(B) 底盘机架
(C) 标记 - 为了指示这两个位置之间的关系,在回转轴承的内座圈和外座圈上作一个标记 (C)。 标记用于使回转操作停止的目标。 参考图 2。
- 起动发动机。
- 将发动机转速刻度盘置于高怠速位置。
- 升高液压油温度至
55° ± 5°C (131° ± 9°F) 。 - 装载铲斗。
铲斗装载重量 ...
50 kg (110.2 lb) - 向任一方向移动回转操纵手柄,直到机器完成一次远离目标的 90 度回转操作。
- 反向移动回转操纵手柄,直到机器完成朝向目标的 90 度回转操作。 将回转操纵手柄移回目标处的空档位置。
- 测量回转轴承上标记之间的距离,获得回转过量的量。 参考图 2。
注: 使用从操作员座椅处可以看见的一点作为目标参考点。
- 清空铲斗并根据图 1 重新定位机器。
- 向各方向移动回转操纵手柄,测量完成一次 90 度回转操作所需的时间。 请参阅表 1 中的技术规格。
- 向各方向移动回转操纵手柄,测量完成三转所需的时间。 请参阅表 1 中的技术规格。
Caterpillar Information System:
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Inverter - Clean
The Connecting Rod Bolt Has a New Look for All 3600, C280, and G3600 Engines {1218} The Connecting Rod Bolt Has a New Look for All 3600, C280, and G3600 Engines {1218}
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Safety
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087} Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087} Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Machine Drift on a Slope - Check
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Travel on Level Ground - Test - Optional Test
C18 Generator Sets Generator Lead Connections
PM820, PM822, and PM825 Cold Planer Machine Systems Rotor Drive Planetary - Remove and Install
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Module - Clean
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Travel on Level Ground - Test
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Mirror
New Software Is Now Used on 3500E Marine Engines {1920, 7620} New Software Is Now Used on 3500E Marine Engines {1920, 7620}
336, 336 GC and 340 Excavator Systems System Schematic
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Swing Speed and Swing Drift on a Slope - Check
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Cylinder Drift - Check
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Window (Front)
A New Alternator Bracket Is Now Used on Certain 374F and 390F Excavator Engines {1405} A New Alternator Bracket Is Now Used on Certain 374F and 390F Excavator Engines {1405}
C9.3B Engines Cylinder Block Cover Group
C7.1 Marine Propulsion Engine Piston Cooling Jets - Remove and Install
336 and 336 GC Excavator Camera
PM820, PM822, and PM825 Cold Planer Machine Systems Rotor Drive Planetary - Disassemble
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Cylinder Speed - Check
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Cab Door