Air Inlet and Exhaust Lines
Show/hide table
| |
| Illustration 1 | g06265900 |
|
Typical example | |
Show/hide table
| |
| Illustration 2 | g03335561 |
|
Bolt tightening sequence | |
Show/hide table
| Item | Qty | Part | Specification description |
| 1 | 16 | 6V-3917 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 2 | 12 | 6J-0934 Bolt | Use the following procedure to assemble the aftercooler assembly and tighten the bolts: 1. Assemble the seals to the aftercooler core. 2. Temporarily secure the bottom seal to the aftercooler with tape. Do not use an adhesive, a silicone lubricant, or any other lubricant for retention of the seal. 3. Assemble the aftercooler with seals to the inlet manifold. 4. Inspect the bottom seal to ensure that the seal is seating correctly in the recess. 5. Install the aftercooler cover. 6. Inspect the upper seal to ensure that the seal is seating correctly in the recess. 7. Install the cover bolts. Hand tighten the cover bolts. 8. Tighten the bolts in a numerical sequence as shown in Illustration 2 to 9. Again, tighten the bolts in a numerical sequence that is shown in Illustration 2 to 10. Remove the tape. |
| 3 | 3 | 5P-8940 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 4 | 16 | 6V-5101 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
Caterpillar Information System:
336, 336 GC and 340 Excavator Systems Pump Control (Output Flow) - Adjust
3516B Generator Set with Dynamic Gas Blending Air Inlet and Exhaust Lines
PM820, PM822, and PM825 Cold Planer Machine Systems Piston Pump (Hydraulic Fan) - Remove and Install
3516B Generator Set with Dynamic Gas Blending Air Starting Motor Pressure Regulating Valve
3516B Generator Set with Dynamic Gas Blending Piston and Rings
3516B Generator Set with Dynamic Gas Blending Cylinder Head Valves
3516B Generator Set with Dynamic Gas Blending Cylinder Head
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Cylinder Liner - Remove and Install
XQP1100 Generator Set Generator Bearing - Lubricate
New Engine Software is Now Used for Certain C175 Generator Set Engines {1920} New Engine Software is Now Used for Certain C175 Generator Set Engines {1920}
New Engine Software is Now Used for Certain C175 50Hz Generator Set Engines {1920} New Engine Software is Now Used for Certain C175 50Hz Generator Set Engines {1920}
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Product Identification
3516B Generator Set with Dynamic Gas Blending Engine Oil Lines
New E-Stop Contact Blocks Are Now Used on Certain Cat® Engines {1408, 7418} New E-Stop Contact Blocks Are Now Used on Certain Cat® Engines {1408, 7418}
3516B Generator Set with Dynamic Gas Blending Cylinder Block
XQP1100 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace - If equipped
XQP1100 Generator Set Fuel System Primary Filter/Water Separator - Drain - If equipped
XQP1100 Generator Set Fuel System Primary Filter/Water Separator - Drain - If Equipped
XQP1100 Generator Set Declaration of Conformity
List of Caterpillar Service Centers for Napier Turbochargers {0374, 1052, 7513} List of Caterpillar Service Centers for Napier Turbochargers {0374, 1052, 7513}
C7.1 Marine Propulsion Engine Alternator Belt - Remove and Install
336 and 336 GC Excavator Cooling System Coolant Level - Check
XQP1100 Generator Set Emergency Stopping
G3516 TA Engine Fuel System Operation