Cylinder Head
Show/hide table
| |
| Illustration 1 | g06265814 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 2 | 130-2608 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature (Reference temperature : |
| 2 | 2 | 130-2607 Valve Seat Insert | During installation, shrunk the valve seat insert with reduced temperature (Reference temperature : |
| 3 | 5 | 3B-0623 Cup Plug | Before assembly, apply Loctite low viscosity core plug adhesive to the bores. |
| 4 | 5 | 3B-0645 Cup Plug | Before assembly, apply Loctite low viscosity core plug adhesive to the bores. |
| D | - | - | Before assembly, apply Loctite low viscosity core plug adhesive to the bores.
Installation depth (D) is |
| E | - | - | Before assembly, apply Loctite low viscosity core plug adhesive to the bores.
Installation depth (E) is |
Show/hide table
| |
| Illustration 2 | g06265819 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 5 | 6 | 131-0420 Cylinder Head Fastener Gp | Use the following procedure to tighten the bolts for the cylinder head:
Before assembly, apply clean engine oil to the threads of the bolts. Tighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of Again, tighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of Again, retighten bolt 1 through bolt 8 in the numerical sequence as shown in Illustration 2 to a torque of Turn bolt 1 through bolt 8 in the numerical sequence to an angle of 180 ± 5 degrees as shown in Illustration 2 . Tighten two bolts (7) only after bolt 1 through bolt 8 have been given the final torque. Tighten two bolts (7) to |
| 6 | 2 | 131-0421 Cylinder Head Fastener Gp | |
| 7 | 2 | 5B-0213 Bolt |
Caterpillar Information System:
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Cylinder Liner - Remove and Install
XQP1100 Generator Set Generator Bearing - Lubricate
New Engine Software is Now Used for Certain C175 Generator Set Engines {1920} New Engine Software is Now Used for Certain C175 Generator Set Engines {1920}
New Engine Software is Now Used for Certain C175 50Hz Generator Set Engines {1920} New Engine Software is Now Used for Certain C175 50Hz Generator Set Engines {1920}
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Product Identification
XQP1100 Generator Set Parallel Operation
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Declaration of Conformity
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Belt Tensioner - Remove and Install
G3516 TA Engine Restriction of Air Inlet and Exhaust
794 AC Off-Highway Truck Machine Systems Wheel and Brake - Remove and Install
XQP1100 Generator Set Generator Winding - Test
XQP1100 Generator Set Coolant Sample (Level 1) - Obtain
3516B Generator Set with Dynamic Gas Blending Cylinder Head Valves
3516B Generator Set with Dynamic Gas Blending Piston and Rings
3516B Generator Set with Dynamic Gas Blending Air Starting Motor Pressure Regulating Valve
PM820, PM822, and PM825 Cold Planer Machine Systems Piston Pump (Hydraulic Fan) - Remove and Install
3516B Generator Set with Dynamic Gas Blending Air Inlet and Exhaust Lines
336, 336 GC and 340 Excavator Systems Pump Control (Output Flow) - Adjust
3516B Generator Set with Dynamic Gas Blending Air Inlet and Exhaust Lines
3516B Generator Set with Dynamic Gas Blending Engine Oil Lines
New E-Stop Contact Blocks Are Now Used on Certain Cat® Engines {1408, 7418} New E-Stop Contact Blocks Are Now Used on Certain Cat® Engines {1408, 7418}
3516B Generator Set with Dynamic Gas Blending Cylinder Block
XQP1100 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace - If equipped
XQP1100 Generator Set Fuel System Primary Filter/Water Separator - Drain - If equipped